Kenmore / Sears Washer Hose Or Tube

This air chamber directs refrigerated air from the freezer to the fresh food section to help maintain consistent temperatures and proper airflow. It replaces a cracked or damaged diffuser that can disrupt cooling performance. What it does:

• Channels cold air through the refrigerator compartments for balanced cooling
• Helps prevent temperature imbalance and warm spots in the fresh food area
• Reduces uneven frosting or condensation caused by airflow leaks
• Restores intended airflow path when the original chamber is broken or missing

• Disconnect power to the appliance before starting any repair
• Typically installs behind interior liners; remove shelves and panels as needed for access
• Handle the part and surrounding trim carefully to avoid damaging clips or seals

Kit contains two 10 feet inlet hoses.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

These replacement 6" FXF vacuum bags capture dust and debris to restore pickup performance and keep the appliance's airflow and motor compartment cleaner. Designed as a direct-fit consumable for compatible bagged upright and canister vacuums. What it does:

• Collects dirt, dust and debris so particles stay contained for easier disposal
• Helps maintain suction by keeping the vacuum's intake and motor chamber clearer
• Reduces dust and allergen re-distribution compared with a torn or overloaded bag
• Replaces worn or full bags that cause reduced capacity, visible dust escaping, or increased odor

• Always unplug the vacuum before removing or installing bags
• Remove the full bag carefully to avoid spilling debris; seal and dispose per local regulations
• Verify correct orientation and secure fit before operating to avoid leaks
• Replace bags regularly; inspect the inlet collar and seals for wear when servicing

This 6-foot rubber hose provides a flexible, durable connection for appliance water/drain routing, helping restore proper flow and reduce leaks. Designed as a direct replacement hose where a 6' rubber line is required. What it does:

• Replaces worn, cracked or brittle 6' rubber hose to stop or prevent leaks.
• Restores flexible routing for water supply or drain lines that need a 6-foot rubber connection.
• Helps eliminate kinks and restricted flow caused by damaged hoses.
• Compatible with standard hose clamps or quick-connect fittings used on many appliances.

• Turn off water and power to the appliance before starting any work.
• Inspect fittings and clamps; replace clamps if corroded or damaged for a secure seal.
• Push hose fully onto the fitting and secure with the proper clamp type; test for leaks before returning appliance to service.

The Drain Hose is an OEM part for Whirlpool washing machines. It is a flexible tube that diverts water from the washer tub during drain cycles, guiding it out of the appliance and into a nearby drain source such as a sink. 

Causes of a bad drain hose can include cracks or abrasions developing over time due to repeated bending and flexing during drain cycles. Mineral or hard water buildup inside the hose can also lead to clogs. Other potential causes are physical damage from rodents, pets, or accidental punctures.

Symptoms of a bad drain hose include:

• Incomplete draining or water remaining in the washer tub after cycles  
• Leaks or drips forming around the drain hose connection point
• Puddles or water pooling under or around the washing machine
• Slow drainage during spin cycles

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washer models.

This replacement 5-foot fill hose with elbow delivers water from the household supply to the appliance, restoring proper fill flow and helping stop leaks from worn or damaged inlet lines. Designed as a direct-replacement assembly for compatible refrigerators. What it does:

• Carries water from the supply valve to the appliance's inlet connection.
• Elbow fitting provides a low-profile connection to reduce kinking at tight inlets.
• Replaces cracked, split, or leaking hoses that can cause slow/no fill or visible leaks.
• Restores reliable water delivery for ice makers and dispensers when the original hose is failing.

• Two 5' fill hoses with elbow fittings (quantity: 2).

• Shut off the water supply and unplug the appliance before starting any work.
• Inspect fittings and replace any damaged clamps; hand-start fittings, then tighten with an appropriate wrench—do not overtighten.
• Check for leaks after turning the water back on and run a fill cycle to verify proper operation.

This inlet hose channels household water to the appliance's fill system. Replacing a worn or leaking hose restores proper water flow and helps protect floors and internal components from water damage.

• Directs water from the household supply to the unit's inlet/fill assembly
• Maintains a watertight path to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or mineral-fouled
• Common symptoms: leaks at fittings or beneath the unit, slow or no fill, intermittent filling, or water-related error messages

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure slowly
• Route the hose without kinks; ensure sealing surfaces and/or washers are clean and properly seated
• Secure connections per the OEM design (compression fitting or clamp); restore water and check carefully for leaks on the first run

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This hose connector joins a refrigerator's/dispenser's water line to internal plumbing, restoring a secure, leak-resistant connection. It replaces cracked or worn connectors to help stop leaks and ensure reliable water flow. What it does:

• Provides a sealed connection between the water hose and the appliance plumbing or valve
• Stops leaks caused by cracked, brittle, or damaged connectors
• Restores proper water flow to the dispenser/ice maker when the connector is the failure point
• Works with hose clamps or fittings already present in the appliance plumbing

• Shut off water supply and unplug the appliance before servicing
• Inspect hose ends and replace clamps or O-rings if damaged; use proper-size clamps for a secure fit
• Hand-start threads, then tighten snugly—avoid over-tightening plastic fittings to prevent damage
• Turn water back on and check thoroughly for leaks after installation

This drain tube funnels and directs excess water away from the appliance to the drain path, helping prevent pooling and water damage. It replaces a worn, cracked or clogged tube to restore proper water flow. What it does:

• Carries water from the appliance's drainage area to the drain outlet
• Helps prevent leaks and interior water buildup from a damaged or disconnected tube
• Can resolve symptoms like water pooling under/behind the appliance or intermittent draining
• Ensures proper routing so water flows to the drain instead of into the cabinet

• One drain tube

• Disconnect power to the appliance before starting any repair
• Turn off water supply and remove any panels needed to access the tube
• Inspect and replace any worn clamps or fasteners; ensure tube is routed without kinks
• After installation, restore power/water and run a test cycle to ensure there are no leaks