Kitchenaid Drip Pan

This dispenser drip tray catches water and minor spills beneath the refrigerator's ice/water dispenser, helping keep the grille area dry and protecting the door from moisture damage or staining.

• Collects drips and splashes from the dispenser to prevent puddling on the door
• Helps reduce staining, mineral residue, and odors around the dispenser area
• Sits in the dispenser grille for easy removal and cleaning
• Common signs it's needed: cracked or warped tray, excessive water on the dispenser shelf, or a missing tray

• Unplug refrigerator or switch off power before servicing
• Lift out the old tray from the dispenser grille; clean area
• Seat the new tray flat and flush in the grille opening
• Verify proper fit and stability before restoring power

This drip tray collects and channels defrost and condensation water away from the refrigerator interior to help prevent pooling and musty odors. Replacing a cracked or warped tray restores proper water management and reduces leak risk. What it does:

• Captures defrost and condensation runoff and directs it to the drain/evaporation area.
• Prevents water from pooling inside the cabinet or beneath the appliance when functioning correctly.
• Common symptoms that indicate replacement: visible cracks or warping, standing water under the fridge, or persistent musty odors.
• Designed as a direct replacement for the factory drip tray specified for the appliance.

• Disconnect power to the appliance before beginning any service.
• Remove any shelves or drawers needed to access the old tray; handle carefully to avoid damaging surrounding components.
• Do not force the tray into place; make sure it seats correctly in the drain channel and sits flat.
• If water problems continue after installing the new tray, inspect the drain path and drain tube for clogs or damage.

A replacement drain pan that captures defrost and condensation water to keep it contained and away from the cabinet and floor. Restores the appliance's normal water-collection path and helps reduce leaks. What it does:

• Collects melting ice and condensation from the evaporator to prevent water from pooling under the appliance.
• Channels collected water toward the drain system so it evaporates or exits as designed.
• Stops common symptoms like puddles or moisture under the unit and musty odors caused by standing water.
• Fits under the evaporator/coil area to restore proper water management.

• Disconnect power to the appliance before service to avoid electrical hazards.
• Remove the required access panels or move the appliance per the manufacturer's guidance to reach the pan.
• Lift out the old pan carefully—it may contain standing water—and position the replacement so the drain outlet and routing match the OEM layout.
• After installation, restore power and check for proper water flow during a defrost cycle; inspect surrounding seals and tubing for proper seating.

A decorative trim ring that restores the original finish and helps secure surrounding components on your appliance. Replaces cracked, faded or loose trim to improve appearance and maintain a proper fit. What it does

• Covers and finishes the edge of a control or opening to give a clean, factory look.
• Holds adjacent trim or components in place to prevent gaps and rubbing.
• Hides wear, scratches or discoloration for an improved appearance.
• Common symptom: visible cracks, chips, or a loose/misaligned trim piece.

What's included

• One trim ring.

Install notes

• Disconnect power to the appliance before starting any work.
• Use basic hand tools; avoid overtightening fasteners to prevent cracking the trim.
• Handle plastic trim carefully to avoid scratches; align tabs/clips before fastening.

The Dispenser Drip Tray is an OEM part for Whirlpool refrigerators featuring built-in water dispensers. Located underneath the outlet spout, it collects any accidental water overflow or spilled cubes to prevent messes. 

Causes of a bad dispenser drip tray involve cracks interfering with its collection surface, or warping preventing it from fully guiding water into the pan below. Damage risks difficulties. 

Symptoms include:

• Water collecting outside the tray area on the cabinetry below
• Dispenser outlet jams from backflow during partial fills  
• Ice cube spills create a slipping hazard on the floor
• Increased effort required to avoid messes during dispensing

This OEM Whirlpool part is also compatible with some GE, Kenmore, and LG refrigerator models.

This drip tray collects defrost and condensation water under the refrigerator to help prevent leaks and water pooling on the floor. It restores proper water capture and drainage for affected fridge models. What it does:

• Catches defrost and condensation runoff from the evaporator or drain system
• Helps prevent water pooling beneath the appliance and potential floor damage
• Works when original tray is cracked, warped, clogged, or missing
• Compatible with factory mounting points and drain alignment when the correct part is used

• One replacement drip tray

• Disconnect power before servicing to avoid electrical shock
• Access may require removing kick plate or lower front panel; follow your model's service instructions
• Slide or snap the tray into place and secure any retaining clips or screws removed earlier

This drip pan is the replacement drain tray that catches defrost and condensation water to help prevent leaks and puddling under the appliance. It restores the unit's normal water collection and drainage path. What it does:

• Collects defrost and condensation water from the evaporator area.
• Directs water toward the drain channel to prevent pooling under the appliance.
• Helps reduce risk of water damage to flooring from leaks or overflow.
• Addresses symptoms like water puddling beneath the unit or visible drips.

• Designed for straightforward replacement; use appliance-specific service manual for exact procedure.
• Disconnect power (and water if applicable) before starting any service.
• Handle carefully to avoid bending tabs or damaging mounting locations.

The Dispenser Drip Tray is an OEM part for Whirlpool refrigerators featuring internal or through-the-door dispensers. Located below the dispenser mechanism, it collects residual liquid and prevents spills. The drip tray's angled design helps direct any drips into its drainage port.

Symptoms of a faulty dispenser drip tray include:

• Puddles or spills below the dispenser area
• Wetness inside refrigerator walls near the dispenser system  
• Mold growth from unattended moisture collecting

Causes may involve cracks that create leaks, clogged drains impair drainage, or a loose or damaged seal around the tray.

This OEM replacement fits many Whirlpool, Maytag, KitchenAid and Kenmore models.

This grille is the external vent trim that covers the appliance's lower air opening, restoring appearance and allowing proper airflow. It replaces cracked, broken, loose, or missing vent trim to keep the front of the appliance looking finished. What it does:

• Covers and protects the lower vent opening while allowing airflow through the front panel
• Restores a finished appearance when original grille is cracked, warped, or missing
• Helps maintain proper ventilation at the appliance base to support cooling components
• Secures into the cabinet openings using factory clips or screws

• One grille

• Disconnect power to the appliance before beginning repairs
• Installation typically requires removing the access panel or toe kick; retain all fasteners
• Align grille tabs with slots and press or screw into place without forcing to avoid breakage
• If clips are damaged, replace them to ensure a secure fit and prevent rattling

This drip tray catches and channels defrost and condensation water to prevent pooling under the appliance. It restores proper water flow and helps protect floors from leaks when placed correctly under the evaporator area. What it does

• Collects defrost and condensation water from the evaporator area
• Directs water to the drain system or evaporation zone to prevent leaks
• Helps stop water pooling or dripping beneath the appliance
• Reduces risk of moisture-related odors and floor damage when functioning properly

• Disconnect power to the appliance before accessing internal parts
• Access from the freezer/refrigerator bottom or back panel per your model's service guide
• Slide or snap the tray into the mounting location; ensure proper alignment with drain channels
• Inspect surrounding seals and drain lines for clogs or damage while replacing the tray

The Drip Tray is an OEM component designed specifically for Whirlpool ranges. Located underneath the range's bottom heating elements, the tray collects moisture, melted cheese, or other baked-on messes during cooking. Its indented surface area and angled drainage grooves route debris toward an easily removed drip cup.

Causes of a bad drip tray can include scorched grease that accumulation makes thorough cleaning difficult or impact dents that cause leakage. 

Symptoms of a bad drip tray include:

• Excessive residue buildup outside the designated drainage path  
• Stains or water marks appearing on surrounding cabinetry
• Drip cup overflowing due to impaired drainage route
• Difficulty removing tray for cleaning of hardened messes

This OEM Whirlpool part is compatible with KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore wall oven and range models.