Kitchenaid Refrigerator Motor

The repair went well. Never made this type of repair before. Took me around 90 minutes to complete. The worst part was winging it on how to disassemble the bottom drawers. On my Kenmore Elite, it has three freezer compartment sliding trays. The other difficult part for me was removing the clipped in part on the back of the freezer panel. Without knowing what to do it was a little frustrating. after getting to the evaporator unit, removing built-up ice and replacing the unit was fairly easy. The... Read more

I received my new part in about 3-4 days. Part was exact match for my existing motor. After watching the installation video on this website I was able to garner the rudimentary directions to replace the motor. The video did not match the exact fridge I had. My fridge did not have the access panel on the interior of the freezer. I had to remove the two screws at the water ice dispenser tray on the outside and slide that unit off the front. Before removing the motor, open the freezer and remove... Read more

After checking the suggested fixes and parts on Appliance Parts Pros, I ordered the defrost thermostat and evap motor for my refrigerator, a Kitchen Aid KSSC42QTS00. Installation was very easy, simply emptying the freezer and removing the access panel in the back bottom half. Upon getting everything open, I found out that the existing evap motor was working fine, so I didn't install that part. I did install the defrost thermometer, which was a 5-minute process. I also cleared out the vent... Read more

The fridge is 20+ years old in a home we recently moved into. It sounded like a motor getting stuck on something or grinding weird... was hoping it wasn't something more serious. Found this site, clicked 'noisy' and got the replacement evaporator fan motor blade as well as the motor evaporator. Turned out I didn't really need to replace the fan blade, but since I had it and ours was old, figured I might as well put in the new parts. Followed the videos here, which were really helpful. The... Read more

Very easy to replace. Take off cover to auger compartment. Unplug power connector from auger motor. Remove four screws holding auger motor to refrig. Put new auger motor in place, insert screws, insert power connector, replace cover. Use ice maker! Read more

Checked and found the evaporator frozen causing the fan to stop working. Took the interior panels off and applied a blow dryer to the ice, once the ice melted I cut the tabs on the grommet holding the fan since everything is thin plastic and replaced the grommet and fan. Placed everything back and found no further issues. Tools I used were a small flat head screwdriver to pry the panels off and a 1/4 socket to remove the center drawer (4), water filter cover (2), and the ice maker (2). Not too... Read more

Originally thought it was the evap fan motor, possibly the control board. Turns out it was the latter but only way to know for sure was to replace fan first. Shipping was fast and the parts were good. Read more

Put in a new motor Read more

Added a new shaft as the old shaft had worn down...........works perfect now. Thank you Easy fix ....no more than 10 mins. Read more

• Noisy

I watched videos to diagnose the noise coming from my refrigerator, then watched videos on how to replace the part, then I ordered the replacement part which came very promptly. The part works perfectly. I am a 73-year old woman, and found this was an easy fix, even on a bottom freezer model refrigerator. The AppliancePartsPro price for this part is a good buy, and I will buy again when I need a part. I have ordered replacement parts from AppliancePartsPro for my cooking range previously and... Read more

The evaporator fan had stopped working and caused the entire area around it to ice up. No air flow was getting from the freezer to the fridge. I replaced the damper control (it was rusted, not sure if it was workign or not) and the evaporator fan. It was a very quick repair once I diagnosed the problem. The most time consuming part was taking all the compartments apart to get to the affected area. Read more

Replaced fan motor Read more

Installed a AP6007346 motor Read more

Replaced evaporator fan in back wall of freezer. Read more

The auger would not turn the dispenser because the screw threads were stripped. I could not re-thread it so I had to replace the entire motor assembly. The video your company provided was extremely helpful not only for fixing the problem but to give me the confidence to do it myself. It was a very detailed video that included all the safety instructions. Read more