Kitchenaid Refrigerator Parts

Replaced the water tube that went from the plastic tubing to the ice cube tray. Found that even though it was the same exact length as the original, there was only an extremely small gap from the end of the tube to a splash board. This may have been the root cause of my problems. Read more

A YouTube video: https://www.youtube.com/watch?v=jIdtNdDXFDk , by a professional appliance repair company described replacement of the freezer drain pipe with Kenmore's (by Whirlpool) revised drain pipe. Ice buildup inside the freezer was caused by warm air beneath the freezer contacting cold air from inside the freezer the resulting condensation freezing and blocking the drain, causing the ice buildup inside. The revised drain tube functions as a p-trap to prevent cold/warm air interaction.... Read more

We have a built-in KitchenAid KSSC42QKS02. Unlike the other Kitchenaid or Whirlpool refrigerators, our valve is located at the bottom and towards the front of the refrigerator. I actually preferred it to be located at the back like the others. It would've been easier to get to. We had to lower the fridge turning the screws(front of the lower panel), so it would sit on the rollers. Then we just simply roll the fridge out, turn off the supply valve, and install the newly bought valve inlet. It... Read more

I ordered 2 new crisper drawers and fronts at around 1 pm and they were delivered by 10 am the next day! It took just a minute for me to figure out how to attach the front to the drawer but it was simple and quick and my fridge is just like new! I was worried that it would take a week or more for delivery of my items once they were ordered but pleasantly surprised that they were there in less than 24 hours! Read more

The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place... Read more

Replaced gasket took 5 minutes. Read more

• Ice maker won't dispense ice
• Ice maker not making ice
• Leaking

After some research on the internet,I found out that the most likely cause was a failed water inlet valve. The refrigerator is quite old so I wasn't going to spend an arm and leg on it to fix it. I was pleasantly surprised to find the part, at a reasonable price, that I needed on this website with a helpful how-to video to boot. The part I needed wasn't in stock. I was followed up with an e-mail stating an estimated time when the part would be released. A week or so later I received the... Read more

Replaced the ice maker. The kit came with everything I needed to replace the ice maker. Parts that did not come with the kit were re-used from the old one. My Whirlpool refrig/freezer is an older model so the wiring harness that came with the kit was different from my existing. So instead of disconnecting the ice maker wiring harness from the freezer, I had to disconnect the harness at the ice maker. That was a b..... Anyway after about 20 minutes, finally unhooked the connector. I had... Read more

Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey. Read more

I replaced the defrost control and heater just to be sure. I usedmthe helpful video and though it took me 2 hours i gotmit done and saved hundreds Read more

Just replaced them - 2 parts in my refrigerator, 1 in my microwave oven. Read more

Removed water catcher, then 4 screws in water/ice vault in door, then removed screws on door side (5) top (2) and bottom (2). Removed stainless door skin. Removed 4 hex head bolts in ice/water vault (containing pads) and 4 bolts on the module immediately above the vault. Pulled the vault and module above out part way to unplug one cable. Then laid on table to unplug pads. From back, each pad has a small indent preventing the pad from being pushed up and removed. Push the small indent with a... Read more

Had the parts I needed at a lower cost Read more

Replaced door closure and door stop. Read more

Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more