Magic Chef Parts

I ordered 1 assembly first and then another broke. so I ordered 2 more and replaced 2 more. The 4th was replaced last summer. I should have ordered 4 and replaced all when the 1st one failed. Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Snaped off and snaped on. Read more

• Will not fill with water

Ordered new inlet water valve and float switch kit. After repairs it now works fine. However the water inlet valve outlet end for fill hose (not water source) and wire connections (supposedly for this unit) were oriented 180 degrees opposite. I had to gently remove the blue plastic valve off the metal support bracket and turn it around and press back in place. Fortunately it appears it was designed for either orientation. Also the solenoid had to be unclipped and also rotated. Again it was... Read more

• Marks left on clothes

After replacing thermal fuse once and having it fail a second time, I had to dig a little deeper to uncover the problem. I checked for blockage in the vent but everything was clear. I did, however, find that the drum had some up and down play in it. After closer inspection, I could see that the front drum seal was actually worn to the point that I could see a gap between the seal and the drum. I figured that the gap in the seal was letting air in and not letting sufficient air flow through the... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

• Not dispensing water
• Leaking

Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more

Touch up paint Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

• Door sweating

Removed old door seal and replaced with the new one I purchased. Read more

• No heat or not enough heat
• Takes too long to dry

Since finding out pulley on motor is factory installed, I had to order a new motor with new pulley on it. I could not remove old blower wheel from old motor, no matter how hard I tried so I had to purchase new blower wheel and new blower housing. I am super happy finding Appliancepartspros.com the prices, and my experience was great! I basically removed everything step by step, and then replaced with the new parts step by step. I had help by watching videos that were provided online before and... Read more

We bought a new ice guard and installed it. It is working really good now. Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

Replaced It With New One Read more

• Door won't close

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more