Magic Chef Parts

I first wanted to get the dishwasher running, before ordering the spring links. So I disassembled the pump / motor assembly to determine the reason the motor would not start. My wife cleaned all of the parts in the pump assembly. I took the motor apart and discovered that the lower bearing ( a sleeve type bearing) was dry and dirty, and was the culprit for the motor seizing. I cleaned up the bearing and lubricated it with SAE 20W. I also packed felt inside the cavity adjacent to the bearing.... Read more

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

It only takes a screwdriver for this repair. Remove the two screws holding the old element, pull it out of the housing, making sure the wires attached to the element do not fall back into the housing when you unclip them. Once you reattach the wires, simply replace the two screws and the job is done. I could not reuse the old screws though since the old ones did not hold the tight (unit is 20 years old and they were simply stripped). I simply increased the thickness of the screws and the new... Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

I haven't yet started to place the dishwasher in place is Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more

• Will not fill with water
• No hot or cold water
• Will not stop filling with water

I called Appliance pros and asked for a diagnosis. They gave one and sent me the part. It took 15 min. and it worked perfectly. Also got super fast delivery on the part. Thank you!! Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

Went on very easily Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

I watched the video at your website. I unplugged the electric first. When I opened up the machine up, It was loaded with lint.I found the source was a hole in the vent tube outside the machine. I fixed that first . The lint had been sucked back into the machine. The first half hour was spent vacuuming out all the lint and then I could proceeded with the motor change. I followed the video exactly. I removed the screws at the two front corners, after lifting the top and controls and tying it... Read more

Watched video and gathered tools I needed. Very simple, and I’m a 72 year old woman! Took maybe 15 minutes to replace both freezer and frig hinge washers. Both doors work like new. Read more

• Element will not heat

Replace burner and receptacle. The product arrived promptly after order and the receptacle came in a factory Whirlpool bag, indicating it was a genuine Whirlpool part. The burner did not have such identification, but works very good. I've placed 3 orders with these folks for various broken appliances, and each one has worked as advertised and performs like new. Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more