Maytag Blower Wheel Or Fan Blade

Clothes not drying or taking too long? This dryer blower wheel circulates air through the drum to dry clothes efficiently. Mounts on motor shaft.

Fix loud rattling or thumping noises in your dryer with a new blower wheel. Common repair when the fan hub breaks or spins freely on the motor shaft.

Dryer not drying or taking too long? A damaged blower wheel disrupts airflow. Moderate DIY repair with basic tools and disassembly required.

Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.

Fix slow drying or no airflow in your dryer by replacing a stripped or cracked blower wheel. Moderate DIY repair restores proper air circulation.

Fix rattling or noisy oven fan with this convection fan blade. Restores proper airflow for even baking temperatures. Mounts directly on motor shaft.

This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:

• Moves air across the heater, through the drum, and out the vent to remove moisture
• Helps maintain proper airflow and temperature inside the dryer
• Common failure symptoms: reduced or no airflow at the exterior vent, longer dry times, unusual scraping/thumping or vibration from the blower area, or overheating/shutoff
• Cracked fins or a stripped hub can cause the wheel to slip on the motor shaft

• 1 blower wheel

• Disconnect power and turn off gas supply before servicing
• Access the blower housing per your model's service instructions; remove the retaining hardware and replace the wheel in the same orientation
• Clean lint from the blower housing and vent path; inspect the motor shaft and blower seal for wear
• Reassemble and verify the wheel spins freely without rubbing; check airflow at the exterior vent

Fix uneven cooling or noisy operation with this refrigerator evaporator fan blade. Restores proper airflow when original blade is cracked or broken.

The Fan Blade is an OEM part for Whirlpool refrigerators. It helps cool down the condenser coils by drawing air over them, providing cooling and temperature regulation inside the refrigerator.

A bad fan blade can be caused by wear and tear, damage from debris or foreign objects, or motor malfunctions. If you notice issues such as poor cooling performance, unusual noises coming from the refrigerator, or the fan not spinning properly, it may indicate a problem with the fan blade.

Symptoms of a bad fan blade include:

• Inadequate cooling or temperature fluctuations 
• Unusual noises coming from the refrigerator
• The fan not spinning or spinning slowly

Replace your faulty fan blade with this genuine OEM part to restore your refrigerator. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This blower housing assembly replaces the blower chamber that supports the blower wheel and routes air through the dryer for proper tumbling and drying. Restores correct airflow and helps reduce overheating or poor drying performance. What it does:

• Houses and supports the blower wheel to direct airflow from the drum to the exhaust.
• Ensures proper airflow for consistent drying and venting.
• Can address symptoms like weak airflow, long dry times, or unusual blower noise when damaged or cracked.
• Works with the blower wheel and motor to maintain lint passage and exhaust flow.

• Disconnect power before inspecting or replacing the blower housing; follow manufacturer safety procedures.
• Access may require removing the dryer front or rear panel depending on model.
• Inspect the blower wheel and motor for damage or obstructions while replacing the housing.

This genuine replacement wheel helps support and guide the dryer drum so it spins smoothly and quietly. Restores stable drum rotation to reduce rubbing, wobble, and noise from worn or damaged support hardware. What it does:

• Supports the dryer drum at the rear or front bearing to maintain proper alignment
• Helps the drum rotate smoothly to prevent scraping and uneven wear
• Reduces vibration and squealing caused by a worn or broken wheel
• Works with the dryer's axle/shaft and housing to stabilize drum movement

• One wheel as shown

• Disconnect power before starting any repair to avoid electrical shock
• Remove the dryer front or rear panel per the service manual to access the wheel
• Inspect related parts (axle, bearing, clips) and replace if damaged for best results
• Use hand tools and avoid forcing parts; follow the manufacturer's instructions

Microwave fan stopped or making noise? This blower wheel restores proper airflow and cooling. Common fix for overheating units. DIY repair in 20 minutes.

Instruction sheet included.

This propeller is the small impeller that mounts to the dishwasher circulation pump to move wash water through the spray arms for effective cleaning. Replacing a worn or damaged propeller restores proper water flow and wash performance. What it does:

• Spins on the pump shaft to circulate wash water through the spray arms
• Restores normal water flow when a cracked or stripped propeller reduces circulation
• Helps resolve symptoms such as poor cleaning, weak spray, or inconsistent water movement
• Works with the pump motor; does not include the motor or pump housing

• Disconnect power and water supply before beginning any repair
• Access the pump assembly from the dishwasher base or cabinet front per your model service instructions
• Inspect the pump shaft and seal for wear; replace damaged components to prevent repeat failure
• Reassemble carefully and test operation

Freezer not cooling evenly or running warm? This evaporator fan blade circulates cold air throughout your refrigerator. Simple press-on installation.