Maytag Damper & Related

This air diffuser assembly directs blower airflow for correct air distribution in the appliance, helping restore proper airflow and reduce uneven drying or heating. Replace damaged or broken diffusers to improve performance and reduce lint buildup. What it does:

• Directs airflow from the blower into the appliance's duct/drum path for even circulation.
• Helps prevent hot spots and uneven drying by guiding air where it's needed.
• Can reduce excessive lint accumulation caused by cracked or warped diffusers.
• Replace when cracked, broken, loose, or when you notice poor airflow, long cycle times, or uneven drying/heating.

• Disconnect power before beginning any repair to avoid electrical shock.
• Access typically requires removing the appliance front panel or cabinet; follow the OEM service manual for disassembly steps.
• Inspect surrounding seals and mounting tabs; replace any damaged hardware to ensure a proper fit and seal.

This upper vent cover replaces the visible duct cover on a range hood to restore proper appearance and help channel exhaust air. It provides a finished look and protects ductwork from grease and debris. What it does:

• Covers the vent duct above the hood for a clean, finished appearance
• Helps direct exhaust up into the duct while protecting internal components from dust and grease
• Use when the original chimney is dented, cracked, or cosmetically damaged
• Reduces visible gaps between the hood and ceiling when properly installed

• Designed to mount to the hood body or chimney assembly; follow OEM mounting points
• May require removal of the hood's grease filters or upper panel for access
• Ensure power is off to the appliance before starting work to avoid electrical hazards
• Replace damaged ducting or fasteners as needed for a secure fit

The Air Damper is an OEM part for Whirlpool refrigerators. It is a component located inside the fridge behind the evaporator cover that controls the flow of cold air circulating throughout the fridge compartment. The damper opens and closes to direct air as needed to efficiently maintain set temperatures.

Symptoms of a bad air damper include:

• Inability to achieve or maintain proper fridge temperatures 
• Condensation buildup inside 
• Frosted evaporator cover
• Warm or cold spots in different areas of the fridge

Causes of a bad damper can be wear and tear of the movable parts over time, failure of the actuator motor that powers it, or damage from accidental blocking of the damper mechanism.

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This damper heater is the heater element used with the refrigerator air-damper assembly to help prevent frost and condensation buildup around the damper. Replaces a failed heater to restore proper damper operation and airflow. What it does:

• Warms the damper area to reduce ice and condensation that can block the damper
• Helps ensure the fresh-food and freezer compartments share airflow as intended
• Commonly replaced when frost or ice accumulates near the damper or when the damper fails to open/close smoothly
• Works as part of the damper/air control system; does not include the full damper housing or actuators unless specified

• Disconnect power to the appliance before replacing this part to avoid shock or injury
• Access may require removing interior panels or the damper housing; follow OEM instructions for your model
• Inspect the damper housing and actuator for damage or ice buildup when replacing the heater

This replacement exhaust vent directs oven/dryer exhaust airflow away from the appliance to maintain proper ventilation and reduce backflow. Restores intended airflow path to help reduce odors and heat buildup around the appliance. What it does

• Channels exhaust fumes and hot air out of the appliance's vent path.
• Helps restore proper ventilation when previous vent is cracked, warped, or blocked.
• Can reduce abnormal heat, odors, or poor drying/cooking performance tied to ventilation issues.
• Limits airflow leak points that can cause noise or vibration during operation.

• One exhaust vent housing.

• Disconnect power (and gas, if applicable) before starting work.
• Inspect and replace any worn gaskets, clamps, or vent hose to ensure a proper seal.

This air guide directs airflow inside the dryer to improve venting and drying performance. Replacing a damaged guide restores proper air path and helps the dryer run more efficiently and quietly. What it does

• Channels warm air from the blower to the drum and exhaust system to maintain proper airflow.
• Helps prevent air leaks that can cause longer drying times or uneven drying.
• Reduces turbulence that may cause rattling or whistling noises during operation.
• Keeps airflow directed away from internal components to limit lint buildup in sensitive areas.

• Disconnect power (and gas supply for gas dryers) before starting any repair.
• Basic disassembly of the dryer cabinet or front panel may be required; follow the model's service manual.
• Keep track of fasteners and gently handle plastic clips to avoid breakage.

This vent tube directs exhaust airflow from the appliance to the vent outlet, helping maintain proper ventilation and reduce leaks. Replace a damaged or crushed tube to restore safe exhaust routing and steady airflow. What it does:

• Channels exhaust air from the appliance to the vent outlet to prevent backflow into the cabinet
• Helps maintain consistent ventilation for efficient operation
• Prevents leaks and reduces the chance of moisture or lint buildup in the appliance cavity
• A worn or damaged vent tube can contribute to poor venting or unusual odors

• One replacement vent tube

• Disconnect power and unplug the appliance before beginning work
• Remove any access panels or obstructions to reach the existing tube; note routing before removal
• Secure the new tube with appropriate clamps or retainers; ensure there are no kinks or sharp bends
• If lint or debris is present, clean the vent path before installing the new tube