Maytag Dishwasher Parts

• Will not fill with water
• Leaking

SCREWED IT ONTO FAUCET Read more

After looking for solutions online and watching some short videos, we decided to open the dishwasher up and try to fix it ourselves. We opened it up and found the circuit board had burned out causing a horrible odor. We ordered our new board, popped it in and we now have a working dishwasher. Hooray! Read more

After some research I found others having the same problem (all buttons worked except the Start button, and the system would work using the "Reset" / "Test" button combination - although I forget the combo). Read more

• Will not drain

I checked the drain hose for blocking at the garbage disposal and then at the connection point to the dishwasher. The hose was clear and nothing was obviously obstructing where the drain hose connects to the dishwasher. At this point I Googled the model number with the term "will not drain" and immediately landed on the AppliancePartsPros.com website. At the Drain & Wash Impeller Kit page amazingly had a video showing the technician replacing the impeller on a dishwasher essentially the same as... Read more

Without knowing exactly what broke I ordered 2 springs and 2 door spring links. I knew the door springs were weak and a parts man told me many years ago to always replace BOTH springs or the one you didn't replace will soon break. It is a simple procedure, just remember how the springs/links are attached. make a simple drawing or take a picture should you need it. I watched two "how to" video's which made it look harder to do than it really is. Turn the circuit breaker off and turn the... Read more

The part was very expensive but replaces quickly. Read more

Ordered a new detergent dispenser that arrived within two days. Removed screws on the inside of door that removes the front door panel. The detergent dispenser is held on by a bracket with six screws. There is one plugin that needs to be disconnected. Everything is reinstalled as before. It work as before. Read more

The Dishwasher Rack Roller was a perfect fit. It took longer to find the part (because I kept typing in wheel) than it took to fix the issue. The old part snapped off and the new part clipped right on. I bought all four rollers even though I only needed one because I'm sure the next one will crack soon. Thanks for the great service. Read more

DIY, changed motor and sump. Put a dab of valve lubricant on seal. Wet outer seal of sump to get it to seat in bottom of tub. Cleaned electrical connectors corroded by leak. Coated connectors with dielectric grease. Had to buy additional clamp. Two clamps came in the sump package but both fit the smaller hose only. Neither fit the large hose. I wish the correct clamps were included. Home improvement store clamp is a little too wide to fit between ridges in large hose. Read more

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

Ordered the part and just clipped it back on Read more

This is a relatively easy repair. Here are detailed instruction to replace the Control Panel. Tools Required: #15 and #20 Torx drivers. (Power tools not recommended) THE INNER SHELL DOES NOT HAVE TO BE COMPLETELY REMOVED There are 10 perimeter screws that secure the inner shell (#15) to the outer shell and six screws, three on each side (#20). Two of these screws secure the Controller Bracket and 4 that secure the spring loaded hinge to the inner shell. These six screws don't have to be... Read more

• Will not drain

Ordered replacement belt from your co. Read an online tip on how to replace the new unbelievably tight belt... 'Carefully loosen the new belt by pulling it upward with your hands and keeping your foot on the opposite end. Then mount the new belt on the pump assembly ABOVE the pump pulley wheel. Stretch the other side of the belt over the motor pulley wheel. Now roll the pump side of the belt down onto the pump wheel. Apply the silicon lubricant included with the new belt and rotate it... Read more

Ordered new top rack and changed out the rusty one. Taking the washer arm off the old one and putting it on the new one was a bit challenging but my husband is good with those things and it went well. Beware that NO instructions come with the rack and there is a bagful of parts that are probably if you want to change rollers or something. Read more

I reviewed the schematic and saw the Volute Seal, and Impeller Seal were the two that were closest my source of water. After watching the video about changing the Impeller/seal I removed the motor, impeller, and volute; I found that the impeller seal was the faulty one in my case. Since I'd ordered the volute and impeller seal kits (as I wasn't sure which it was) I installed both while I had it apart. Runs great, no water - simple to do. The seal changes took about 20 minutes. The only... Read more