Maytag Dishwasher Parts

• Noisy

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

I discovered that the manifold was not connecting with the water supply,so the dishes in the upper tray were not being washed. This was caused because the rear hanger on the manifold had broken and it did not lineup properly into the water supply connection in the back of the dishwasher. I removed the manifold and found that it had two part numbers stamped on it. I searched on both part numbers and received a hit on the second part number. The photo looked exactly like my manifold so I... Read more

I replaced the rear tube that feeds water to the top and middle spinners, and this appears to have fixed the problem. The middle spinner, which is attached to the bottom of the top rack, has a tube that connects to a hole in the middle of the rear tube.This hole has a rubber flap and I noticed that this flap was wide open. The tube under the tray has a straight edge protruding from it at the back. This edge pushes the flap open and I suspect that when the water is flowing, this edge rotates... Read more

Removed and replaced diverter motor. Ops check good, no more leaking. I'm guessing the seal was the problem but diverter ruined (water residue) from leaking over the last 5 years??? This seal is only available if you buy the tub so followed another review - removed diverter then gently pried out the seal, cleaned and then lubed with silicone grease. Also turned the seal 180 degrees or the opposite way before reinstalling the diverter and then wrapping it all back under the counter. Read more

1, Removed roller tray front stoppers from each side. 2. Pulled out empty top rack from dishwasher. 3. Removed existing top rack roller. 4. Inserted new roller where old one was located. 5. Repeated for each roller. 6. Inserted top rack back into dishwasher. 7. Enjoyed using both racks again!! Read more

I first wanted to get the dishwasher running, before ordering the spring links. So I disassembled the pump / motor assembly to determine the reason the motor would not start. My wife cleaned all of the parts in the pump assembly. I took the motor apart and discovered that the lower bearing ( a sleeve type bearing) was dry and dirty, and was the culprit for the motor seizing. I cleaned up the bearing and lubricated it with SAE 20W. I also packed felt inside the cavity adjacent to the bearing.... Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more

Ordered exact part & installed Read more

I haven't yet started to place the dishwasher in place is Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

Simple, took 2 min to remove then reinstall the new sprayer. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Won't start
• Door latch failure

Discovered that the common cause of the problem was the latch in the door. Found a video online that showed the exact procedure for my model dishwasher. Ordered the part from AppliancePartsPros on a Thursday afternoon and it was in my hands by noon on Friday. Carefully took the door apart, compared parts, reassembled, and the joy on my wife's face was priceless when the dishwasher started up without doing anything special. Do not be afraid to attempt this repair. Read more

Just slipped the kick plate into place and used screws to secure it. Very easy. I'm a realtor and tackled this for my elderly client. Shipping was quick. From ordering to installing was less than a week. Read more