Maytag Range Parts

Replaced them but Jennair knobs are really cheap and I’m sure I’ll have to keep replacing them. Sad that such an expensive appliance has such cheap knobs. Read more

Installed the new pans and replaced the coils. My Jennaire looks like new. Only took minutes and made such a difference. Read more

Of course, before disassembling anything, I unplugged and turned off the gas supply. To replace the spark electrode, I removed the drip pan/surface to gain access to the burner assemblies. Next, I unscrewed (with a 1/2" open-end wrench, I think) and disconnected the gas supply tubing from the burner assembly with the cracked electrode, and then unscrewed the assembly itself from the base surface. With the assembly detached, I flipped it over and removed the screw that secured the cracked... Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

The lightbulbs were a problem for me as I did not know if they were 12 V or 120 V. But the interactive parts diagram on the website was very helpful and allowed me to order the correct bulbs very rapidly(120V is correct). They were very easy to change out except for the fact that I needed to have my 12-year-old son do part of it since his hands are smaller than mine.(and it is always good for sons to work with dads even on small projects like this.) The cooking element was also amazingly easy... Read more

Replaced the thermst-fix and the thermal fuse oven now works great Read more

Your on line video pointed out the problem, how to test, and how to replace the element. I ordered the part it came the next day. Wife is very happy. Read more

I replaced the old burner with the new burner assembly which included the ignighter. The screw that held the old ignighter was frozen into the old burner such that just the ignighter could not be replaced. Be care full removing the screws to the burner as they also may be frozen and tend to snap off instead of unscrewing. You will need to drill an tap new holes. Read more

Ordered a replacement panel. Item arrived exactly as described. Used the Youtube instructions. Took all of 5 minutes to replace. Thanks! Read more

Replaced fuse. It took much longer to get the oven out of the wall to access the fuse and replace the front panel than to do the repair. This fuse failed at the end of the cleaning cycle for the bottom oven and left the door locked because the open fuse removed the 120v power from the control board. The locked door made it impossible to remove one of the screws holding the wall oven in place. However, after I ground off the head of the screw behind the edge of the locked door I was able to... Read more

You have to take the knob off the broken part, then buy the new switch element and fix it. To do this you turn the power off, take out 6 fasteners to release the front panel of the stove and replace the switch element. Then put it all back together. Very simple. But if the knob was designed better it would not have broken in the first place. It looks nice, but this is the third time I have had to fix one. Read more

I replaced the old burner with the new burner assembly which included the ignighter. The screw that held the old ignighter was frozen into the old burner such that just the ignighter could not be replaced. Be care full removing the screws to the burner as they also may be frozen and tend to snap off instead of unscrewing. You will need to drill an tap new holes. Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more

Removed the light covers, removed burned out bulbs, inserted replacement bulbs, reinstalled light covers. Read more

Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem. Read more