Maytag Refrigerator Parts

A bit of online research and some component testing narrowed my issue down to either a faulty ice maker or a bad supply valve. Appliance Parts Pros had both of these, at reasonable prices, so I purchased and replaced both items. I recommend watching online videos to get a sense of what to do, and how to go about doing it. The repairs were relatively easy, other than this being a bottom freezer model hence the ice maker was difficult to access: I removed the freezer door (four screws) to get... Read more

Watched video by AppliancePartsPros.com and fully understood what had to be done. This company is an excellent example of how a company should be run. Very helpful and professional team support. A model for a company that wants to offer customer service! Read more

Replace glass took no time at all less then 5 minutes no major tools required Read more

Replaced water valve and ice maker Read more

I had a slow leak at the water inlet valve where the water line from the filter assembly connected to the water inlet valve. I determine that the water line had scratches in it which caused it to not seal. Had to buy the entire reservoir and filter assembly to get that water line. The replacement was smooth. It took about 30 minutes to swap out and it fixed the leak. Read more

Given all the symptoms, we figured that the control board went out. First, unplug the refrigerator. The control board was easy to access by removing a panel on the back of the fridge. I unplugged all the connectors and used a putty knife to release the board from the plastic retaining clips. There was some browning on the underside of the board and the back of the refrigerator that suggests one of the capacitors on the board blew. Install the new board by pressing it into the retaining clips... Read more

• Won't start
• Fridge too warm
• Freezer section too warm

Replaced capacitor and starting relay on the compressor in 15 minutes. The problem may have just been the capacitor, but rather than trying that and if it didn't solve the problem i would have had wait for the relay. Read more

First, I watched your VERY HELPFUL videos showing exactly how to remove and assemble the parts. I removed the salvageable parts from the old shelf frame and reassembled it. Read more

Ordered part and replace it Read more

Finding the part was puzzling. AppliancePros had the relevant manufacturer's part schematics handy on-line through which I quickly identified and order the replacement part. But the best aspect was AppliancePros' Amazon-like excellence in a) pricing and b) swift delivery (with precious tracking included). Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more

Purchase a new one and installed per your video on Youtube. Great and easy. Read more

Used U-Tube diagnostic clips to diagnose that most likely problem was a worn Evaporator Fan Motor which is located in the freezer back wall, located in the top third of the unit. I removed 6 hex head screws from the freezer's interior back panel that covers the evaporator coils. The cover is located in the lower 2/3s of the back wall. Removed all shelving. Also removed screws that held in shelf supports on one side of the freezer wall. I then removed the back panel. You may need to... Read more

By replacing it Read more

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more