Maytag Washer Latch, Catch, Lock Parts

The Latch is an OEM part for Whirlpool dishwashers. It secures the dishwasher door during operation, ensuring it remains closed to prevent water leaks and maintain optimal washing performance.

Causes of a bad latch can include wear and tear from regular use, physical damage from forceful closing, or corrosion from exposure to moisture. A faulty latch can compromise the dishwasher's ability to seal properly, leading to potential leaks and operational issues.

Symptoms of a bad latch include:

• The dishwasher door not closing or latching properly
• Water leaking from the door during cycles
• The dishwasher not starting or stopping mid-cycle
•  A loose or misaligned door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Strike is an OEM replacement part for Whirlpool front-loading washing machines. It is the metal component integrated into the washer cabinet that securely receives and holds the washing machine door shut during cycles. 

Causes of a bad door strike can include normal wear over time. Excessive force on the door or damage to strike mechanics may compromise its integrity.

Symptoms of a failed door strike include:

• Gapping at the door seam permitting water leaks and reduced cleaning 
• Inability to fully latch closed for safety-certified operation
• Loose motion, impact damage, or misaligned connecting pieces  
• Recurring errors involving the door lock mechanism

This is the male piece to the door latch assembly on a front load washer. For the door latch assembly order WP8182634.

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers.

The Lid Strike is an OEM part for Whirlpool washing machines. This small yet essential component ensures that the washer lid is securely latched, allowing the machine to operate safely and effectively. The lid strike interacts with the lid switch, enabling the washer to detect when the lid is closed and allowing the washing cycle to proceed.

Over time, the lid strike can become worn out or damaged due to regular use, accidental force, or misalignment. A faulty lid strike can prevent the washing machine from recognizing that the lid is closed, thereby hindering the operation of the machine.

Symptoms of a bad lid strike include:

• The washer not starting or stopping mid-cycle
• Error messages indicating the lid is open when it is closed
• Difficulty in latching the lid securely
• The lid strike appearing broken or misaligned

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Lid Lock Assembly is an OEM replacement part for Whirlpool washing machines. It prevents the lid from opening during the wash cycle, ensuring the safety of the user and preventing leaks.

Causes of a bad lid lock assembly can include wear and tear over time, damage to the assembly or its components due to mishandling or impact, or electrical malfunctions.

Symptoms of a bad lid lock assembly include:

• The lid not locking properly
• Difficulty opening or closing the lid
• The washer starting or continues to run even when the lid is open
• Leaks from around the lid
• Washer will not start

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cam fits between the refrigerator door and hinge to create smooth, controlled movement and a self-closing feel. Replacing a worn cam restores proper door alignment and gasket contact to help maintain temperature and reduce frost or moisture.

• Works with the hinge to guide door movement and provide a detent/self-close action
• Helps keep the door aligned for an even gasket seal and smoother opening/closing
• Worn cam symptoms can include clicking/popping at the hinge, a door that sags, swings open, or won't fully close without lifting/pushing
• Contribute to temperature fluctuations or condensation if the door doesn't seal consistently

• Disconnect power; unload and support the door to prevent damage
• Remove hinge cover and fasteners; lift the door as needed to access/replace the cam
• Note cam orientation and reuse original hardware, spacers, and shims
• Adjust leveling/hinge if needed

The Door Lock is an OEM part for Whirlpool washing machines. This part securely locks the washer door during operation. This safety feature prevents the door from being opened while the washer is running, thereby avoiding water spillage and ensuring that the washing cycle can proceed without interruption.  

Causes of a bad Door Lock can include electrical failures, mechanical wear and tear, and damage from forced attempts to open the door while it is locked.  

Symptoms of a bad Door Lock include:

• The washer door not locking or unlocking properly
• The washing machine failing to start its cycle due to the door not being recognized as closed
• An error code indicating a door lock malfunction displayed on the washer

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Door Strike is an OEM component specifically designed for Whirlpool top-loading washing machines. The door strike functions as a secure contact point when closing the door.

Causes of a bad door strike include wear from chafing rubber seals collecting residue over time, loosened fasteners, or impact warping from repeated closure force.

Symptoms of a bad door strike include:

• Misaligned or loose door that does not close fully 
• Door unable to latch or seal properly
• Potential water leaks due to ineffective seal

This part also fits KitchenAid, Roper, and select Kenmore top-load models.

Plunger for lid switch.

This latch secures the door closed and signals the control that it's safe to run. Replace a worn or broken latch to restore solid door engagement and reliable operation.

• Engages the strike to keep the door firmly closed during use
• Provides the "door closed" signal to allow cycles to start
• Common symptoms: door won't latch or pops open; must hold door shut to run; "door open" message or won't start with door closed
• Helps ensure safe, consistent operation by maintaining proper door engagement

• Disconnect power before servicing; the appliance is fully de-energized
• Access the latch from the door/console area; note fastener and wiring locations for reassembly
• Inspect/align the door strike so the latch engages smoothly
• After installation, close the door and run a short cycle to confirm proper engagement and operation

This bezel is a trim piece that finishes and protects the opening around a control or feature on the appliance's panel. Replacing a cracked or missing bezel restores a clean look and helps the mating control sit securely and operate properly.

• Frames the control or opening and covers raw edges for a finished appearance
• Helps keep the associated knob/button or trim aligned and seated
• Shields internal components from dust, splashes, and minor impacts
• Replace if cracked, warped, loose, or missing; symptoms can include a wobbly control, visible gaps, or cosmetic damage

• Disconnect power at the breaker before servicing; allow any hot surfaces to cool
• If applicable, pull off the knob or remove adjacent trim to access the bezel
• Release locking tabs or remove mounting screws carefully to avoid scratching the panel
• Align the new bezel with tabs/orientation marks and snap or fasten into place; reinstall parts and test

This lock cam is a small actuator that drives the appliance's door-lock mechanism. It translates the lock actuator's movement into a positive latch, helping the door lock securely when required and release correctly so cycles start and finish properly.

• Interfaces with the lock actuator and latch to engage and release the lock
• Wear, cracking, or rounding can cause the lock not to engage or to stick
• Common symptoms include a door/lid that won't lock or unlock, loose lock lever, clicking without latching, or door/lock-related error messages
• Restores proper linkage travel and switch actuation when the original cam is worn or damaged

• Disconnect power to the appliance before servicing
• Access the lock mechanism per your model; note the cam's orientation and any springs/linkages
• Install the new cam fully seated and ensure it engages the actuator and latch smoothly
• Reassemble, restore power, and test lock operation

This in the male piece on the front panel. For the female piece on the door order WPW10111905.

This door lever actuates the latch/switch when the door closes. If it's worn or broken, the appliance may not sense a closed door and won't start. Replacing it restores proper door engagement and safe, reliable operation. What it does:

• Engages the door latch/switch mechanism so the control knows the door is closed
• Helps ensure the unit only runs with the door fully shut
• Replaces cracked, bent, or missing levers that prevent proper door sensing
• Common symptoms: won't start, must hold/push door to run, "door open" indicator stays on

• 1 door lever

• Disconnect power before servicing
• Access the latch/switch area; note the original lever's orientation and any spring
• Transfer and reuse existing hardware if needed; install the new lever in the same position
• Close the door and test for proper start/stop operation

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

Replacement lid strike assembly that secures the washer lid so the machine can operate reliably. Restores proper lid engagement to help prevent the washer from stopping mid-cycle or the lid from coming unsecured during use. What it does:

• Engages with the lid latch to hold the lid closed during wash and spin cycles
• Restores proper lid alignment and secure closure when the original strike is worn, broken, or missing
• Common repair for symptoms like the lid not staying latched, the washer refusing to start, or a rattling/slipping lid

• Disconnect power before servicing the washer
• Typically installs at the lid/hinge area; may require removing the top panel or console for access
• Use basic hand tools and take care around springs and hinges to avoid injury

Lid strike assembly that provides a secure catch for the washer lid so the lid latch/switch can engage, restoring proper lid closure and allowing the washer to start and complete cycles reliably. What it does:

• Serves as the catch point the lid latch engages to keep the lid closed during operation
• Enables the lid switch/lock to detect a closed lid so the machine can start and run
• Common replacement when the lid won't stay closed, the washer won't start, or lid engagement is intermittent
• Matches original mounting points for direct replacement and consistent operation

• Disconnect power to the appliance before attempting any service
• Access the strike by opening or removing the top/control panels as required for your model
• Align the strike with the lid latch, secure with the original fasteners, and ensure smooth engagement
• Reconnect power and run a short cycle to ensure proper lid detection and operation