Mtd Parts

Hex screw for lawn mowers, tractors, and snow blowers. Replaces worn, corroded, or missing screws on engines and housings. Identical fit for secure assembly.

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

Deck belt cover for riding mowers with 42-inch decks. Shields the belt assembly from debris and damage. Replace if cracked, broken, or missing.

This air filter consists of an internal plastic frame with a foam mesh cover that captures dust and dirt. The outer, washable pad covers an accordion-style inner filter that removes even finer particles. An air filter keeps particles in the air from getting sucked into the motor, where friction will cause wear and tear to the engine. However, a filter has a limited life cycle. Eventually, it gets clogged up, which leads to limited airflow and decreased efficiency. If the engine is bogging down when it is revved up, a clogged air filter might be to blame. Simply install a new air filter and see if the motor performance improves. It is recommended to preemptively replace the air filter every spring so a clogged filter never puts a halt to a job in progress. This is an OEM part, sourced directly from MTD, and it is sold individually. In addition to MTD lawn equipment, it has also been used by other manufacturers, including Craftsman, Yard Machine, and Yard-Man.

Installing a brand-new air filter keeps the engine in top running condition. When the machine is in operation, the vacuumed air goes through the air filter. Any dirt or dust is left in the filter media. Over time, the filter will become dirty and can no longer provide the same filtering efficiency as before. If left ignored, the tiny particles could clog the engine and the carburetor. You may experience misfires and no engine start-up. An air filter replacement is cheap and easy to do. Simply remove the air cleaner cover and take out the dirty filter. Insert the new filter into the housing. This replacement will take less than 5 minutes. A screwdriver will be needed. The MTD 951-10298 Air Cleaner Kit is a genuine air filter from MTD. Each kit comes with one paper filter and one foam filter. The foam filter can be cleaned with water and detergent. The paper filter, however, needs replacement at least once a year. This air filter kit is compatible with Cub Cadet, PowerMore, and Troy-Bilt. It can also work with other garden equipment like wheel string trimmers, chipper-shredder vacuums, and log splitters.

Air cleaner housing protects the air filter from debris and damage. Replace if cracked, warped, or damaged to maintain proper filtration. Verify fit.

Replacement front wheel assembly for walk-behind mowers. Installs on the front axle to restore mobility. Replace if wheel is cracked, worn, or damaged.

Replacement wheel assembly for walk-behind mowers and lawn equipment. Installs on axle to restore mobility. Order when wheel is cracked, broken, or worn.

Mower vibrating excessively or blade loosening? This blade adapter connects the motor shaft to the mower blade. Simple DIY repair, typically 15 minutes.

This rubber seal ring sits within the carburetor assembly to prevent fuel and air leaks. Replace when the engine runs poorly, won't start, or you notice fuel leaking from the carburetor area.

Auger not turning or moving slowly? This snowblower worm gear connects the driveshaft to auger blades. Moderate DIY repair restores snow ejection.

The cable seen here is an authentic replacement that is sourced from the manufacturer. This control cable is used for lawn mowers. It will pivot to pull the belt idler pulley, which will fasten the belt and spin the mower's cutting blades. When the cable is not working properly, it could mean that the blades will not spin properly and not provide the mower with the cutting capability that it should have. The cable that comes with the mower tends to be durable, but this does not mean that it will not need to be replaced at some point. Many things could happen to the cable that would require a replacement. The spring might start to wear out, for example. The cable could become frayed or corroded, as well. Owners should always make sure they are wearing gloves when replacing this part. They will need a screwdriver and pliers to complete the repair. The cable is a genuine OEM replacement part that is sold individually. This cable will work with more than 130 models of mowers. Brands with compatible models include Craftsman, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut.

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

5-inch diameter deck roller wheel for lawn tractors and riding mowers. Replaces cracked, worn, or missing deck wheels that support smooth cutting deck operation.

Bell washer adds spacing on shafts in lawn tractors, tillers, mowers, and chipper shredders. Replace if washer is missing, worn, or damaged during maintenance.