Parts for Lg WT7500CW/00: Outer Case Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This tapping screw fastens appliance panels and components for a secure, lasting hold. Replace stripped, rusted, or missing hardware to restore proper fit, reduce vibration and rattling, and keep brackets, covers, and trim tightly in place.

• Fastens metal or plastic panels, trim, or brackets to the appliance cabinet/frame
• Cuts its own threads in pre-drilled holes for a tight, reliable fit
• Helps maintain alignment and reduce movement that can cause noise
• Replace when the original screw is missing, stripped, corroded, or will not tighten

• Disconnect power and shut off water/gas before servicing
• Match the screw's position and length to the original hardware
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any washers or spacers from the original assembly if present

This holder assembly is a direct replacement mounting bracket that secures refrigerator internal components so they stay properly positioned and function reliably. Replaces a cracked or loose bracket to restore stable support and reduce rattling. What it does

• Secures internal components or assemblies to the cabinet to prevent shifting and vibration
• Restores proper alignment when a cracked or broken holder causes loose parts
• Helps stop rattling, knocking, or intermittent contact caused by a failed mount
• Works as a structural replacement—matches OEM fit and mounting points

• One holder assembly

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove nearby shelves, bins, or trim for access as needed; keep small fasteners organized
• Typically installs with basic hand tools; do not overtighten fasteners to avoid cracking
• If the part attaches to electrical components, verify connectors are secure before restoring power

The Pulsator Cap is an OEM part for LG washing machines. It is designed to secure the pulsator (or agitator) in place, ensuring proper movement of the wash plate during the wash cycle. This component helps in the effective distribution of water and detergent, promoting thorough cleaning of clothes.

You should replace this pulsator cap if it becomes damaged, lost, or worn out. Causes of a bad pulsator cap can include regular wear and tear, exposure to heavy loads, or damage from improper handling. A compromised cap can lead to inefficient washing and potential damage to the pulsator.

Symptoms of a bad Pulsator Cap include:

• The pulsator becoming loose or dislodged
• Unusual noises during the wash cycle
• Clothes not being cleaned properly
• The washer experiencing imbalance issues

This OEM LG part is also compatible with Sears/Kenmore models.

This top bracket secures the appliance's top panel and helps keep upper components properly aligned for stable operation. It provides a direct replacement for damaged or bent mounting brackets to restore panel fit and reduce noise. What it does:

• Holds the top/panel in place to prevent movement and misalignment
• Helps reduce rattling or vibration caused by a loose top panel
• Supports attached controls or components mounted near the top
• Restores proper gap and fit between the top panel and cabinet

• Disconnect power (unplug or shut off circuit) before starting any repair
• Typical installation requires removing the top panel and fastening bracket with standard screws; use appropriate hand tools
• Inspect surrounding fasteners and mounting points; replace any stripped screws or damaged clips

The Customized Screw is an OEM part for securing the wash plate in LG washing machines. This screw maintains the wash plate's position and stability during the washer's operation. The Customized Screw ensures the wash plate performs efficiently, contributing to the effectiveness of the washing process by enabling proper agitation and circulation of clothes.

Causes of a bad Customized Screw can include wear and tear over time, especially from the constant motion and stress during the wash cycles.  

Symptoms of a bad Customized Screw include:

• The wash plate becoming loose or detached
• Ineffective washing due to improper motion of the wash plate
• Unusual noises during the wash cycle indicating a loose component

This OEM LG part is also compatible with some Kenmore models.

This damper controls airflow between compartments to help maintain consistent temperatures and efficient cooling. It replaces a worn or failed damper to restore proper air distribution and reduce temperature swings. What it does:

• Regulates airflow between freezer and fresh-food compartments for balanced temperatures
• Can cause uneven cooling or warm fresh-food compartment when faulty
• May click, stick, or fail to open/close if broken or obstructed
• Works with the refrigerator's control system to adjust airflow based on settings

• Disconnect power before beginning any service to avoid electric shock
• Handle the damper and housing carefully to avoid damage to plastic fins or linkage
• Note orientation and actuator connection before removal to ensure correct reassembly
• Test operation after reinstalling by restoring power and cycling temperature controls

Replace a damaged or stripped leveling foot with this leg assembly. It supports the appliance and adjusts for height so you can level it on uneven floors, restoring stability and helping reduce vibration, noise, and movement. What it does:

• Provides adjustable height to properly level the appliance
• Supports the cabinet/frame to keep all corners in firm contact with the floor
• Helps reduce rocking, walking, vibration, and rattling noises
• Fixes: appliance wobbles or is unstable; foot is cracked/missing; threads are stripped; cannot be leveled

• One leg assembly

• Disconnect power and, if applicable, turn off the water supply before servicing
• Carefully tilt or raise the appliance; protect the floor from scratches
• Unscrew the old leg; thread the new leg in by hand and adjust height to level
• Ensure all feet contact the floor firmly and the unit is stable before use

This hardware washer sits beneath a screw or nut to spread load and help keep fasteners tight inside your appliance. Replacing a bent or missing washer restores a secure fit and can reduce vibration-related noise. What it does:

• Distributes clamping force to protect mounting surfaces
• Helps resist loosening from vibration and movement
• Restores proper alignment when a washer is damaged or missing
• Common symptoms: loose or wobbling parts, rattling noises, screws backing out

• 1 washer

• Disconnect power; if working on a washer, also turn off water supply
• Note the original hardware stack order and take photos for reference
• Place the washer between the fastener head or nut and the part being secured
• Tighten to manufacturer guidance; avoid overtightening to prevent damage

This replacement holder is a small mounting bracket used to secure components inside the appliance, restoring proper alignment and support so parts sit firmly and operate as intended. Ideal when a cracked or worn holder causes instability. What it does

• Secures internal components or assemblies to prevent movement or vibration
• Restores proper alignment when a damaged holder allows parts to sag or shift
• Helps reduce noise from loose or unsecured components
• Commonly replaced when the original holder is cracked, broken, or missing

• Turn off and unplug the appliance before beginning any repair.
• Inspect surrounding clips and fasteners; replace any damaged hardware for a secure fit.
• Use appropriate hand tools; avoid forcing parts to prevent further breakage.

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

This front panel assembly replaces the damaged or worn control panel to restore the appliance's user interface and cosmetic finish. It houses the buttons, display opening, and mounting points needed for normal control operation. What it does:

• Replaces cracked, broken, or cosmetically damaged front control panels
• Restores button and display alignment for reliable user input and clear readout
• Helps prevent dust and moisture from reaching internal controls
• Addresses issues where the console bezel is loose, warped, or otherwise compromised

• Disconnect power (and water if applicable) before beginning any repair.
• Some installations require removing the control board or console clips—keep screws and small parts organized.
• Handle the panel carefully to avoid scratching the finish or damaging the display opening.

This genuine hardware washer installs at the specific joint shown in your model's parts diagram. It spreads clamp force and keeps the connection aligned and secure to support smooth operation of the related component. What it does:

• Distributes fastener load and protects mating surfaces from damage
• Maintains proper spacing and alignment within the assembly
• Helps resist loosening from vibration over time
• Clues it may be needed or worn: loose/rattling parts, unusual vibration or noise, or visible wear at the fastener location; on some models, seepage at that joint

• 1 washer

• Disconnect power and turn off water supply before servicing
• Support the assembly, remove the fastener, and install the washer in the same orientation
• Tighten the fastener snugly without overtightening; replace any damaged bolts, nuts, or seals

This front decor panel is the exterior trim piece that restores the microwave's finished appearance and covers the control/magnetron cavity edges for a clean look. It replaces damaged or discolored front trim to improve aesthetics. What it does:

• Replaces the microwave's front trim to restore the appliance's factory appearance.
• Covers and protects the control/door edges from dirt and cosmetic damage.
• Helps maintain a consistent finish when the original panel is dented, scratched, or faded.
• Matches OEM fit and attachment points for straightforward replacement when the correct part number is used.

• One decor panel (front trim) as shown.

• Disconnect power (unplug or switch off breaker) before starting any work.
• Remove the microwave door or control housing per OEM service instructions to access mounting screws; keep hardware separate for reassembly.
• Handle edges carefully to avoid cuts and protect finish from scratches; use soft cloths when aligning the panel.

This knob assembly replaces a damaged or missing control knob so you can securely and accurately set cooktop or oven controls. Durable replacement restores tactile grip and proper engagement with the control shaft. What it does:

• Replaces a cracked, melted, stripped, or loose control knob that won't turn or stay in position
• Provides correct spline engagement for consistent selection of heat or function settings
• Restores safe, predictable control response when adjusting temperature or burner level
• Helps prevent accidental slips or improper control input from worn knob surfaces

• One knob assembly

• Disconnect power to the appliance before servicing; for gas ranges also shut off the gas supply
• Pull the old knob straight off the control shaft; align splines and push the new knob fully onto the shaft
• If knob resists, verify correct orientation—do not force or hammer the part into place
• If the control shaft or switch is damaged, replace the underlying control/switch assembly rather than relying on the knob

The Main Display Board is an OEM component specifically designed for LG front-loading washing machines. It powers the interactive control panel and digital display interface.

Causes of a bad Main Display Board can include component degradation from extended use, water damage compromising circuits over time, or unexpected power surges overloading electronics.

Symptoms of a bad display board include: 

• An unreadable, frozen, or malfunctioning screen  
• Inability to change settings using touch or button controls
• Frequent error messages obscuring cycle instructions

Replacing with this genuine LG board restores simple, clear interaction through an intelligent control panel. This replacement ensures the interface continues providing trouble-free assistance. It is also compatible with Sears/Kenmore models.

This inner tub hub connects the washer's inner drum to the drive assembly, providing a secure rotational link so the drum can spin properly. Replacing a damaged hub restores drum stability and reduces noise or wobbling. What it does:

• Secures the inner tub to the drive shaft so the drum turns with the motor
• Prevents excessive movement, vibration, and scraping noises caused by a worn or broken hub
• Helps correct spin-related issues like uneven spinning or the drum not engaging
• Works with the tub assembly and other drive components to maintain proper drum alignment

• One inner tub hub

• Disconnect power and water supply, and fully drain the washer before starting
• Replacement generally requires removing the outer tub/inner tub assembly and transferring seals or gaskets as needed
• Use proper tools and follow OEM service instructions
• Inspect surrounding components (seals, bearings, suspension) and replace if worn to prevent repeat failure

The Drain Pump Assembly is an OEM replacement part for LG washing machines. As an important part of the washer drain system, it drives the pumping action removing water from the tub at the end of each cycle.

Causes of drain pump failure include normal wear from continuous operation over time, foreign debris potentially clogging the impeller cavity, or mineral/scale buildup inhibiting pump function.

Symptoms of a faulty drain pump can include:

• Washer fails to fully drain water at the end of cycles
• Excess water remains in the tub requiring manual emptying
• Abnormal grinding/knocking noises emit from below the tub

This OEM LG part is also compatible with some Sears/Kenmore model washing machines.

This single wire harness restores the electrical connections between components in an appliance, allowing circuits to operate normally and helping resolve power or intermittent control issues. It's a direct-fit replacement used where the original harness is damaged. What it does:

• Re-establishes electrical pathways between controls, sensors, motors or lights
• Helps stop intermittent operation caused by frayed or broken wires and poor connector contacts
• Replaces burned, pinched, or otherwise damaged harnesses that can trigger no-power or failed-function symptoms
• Maintains factory routing and connector interfaces for proper fit and function

• One single wire harness

• Disconnect power (unplug or shut off breaker) before starting any work
• Follow factory routing; avoid sharp edges and heat sources that can damage wiring
• Ensure all connectors are fully seated and locked; secure harness with clips or ties as originally installed

This spring-style hose clamp secures flexible hoses to fittings to help maintain a watertight connection and prevent leaks. A simple replacement when the original clamp is worn, bent, or no longer holds tension. What it does:

• Holds washer, drain, or water-supply hoses firmly on barbs and fittings
• Restores clamping tension to stop drips or slow leaks at hose connections
• Prevents hoses from slipping off under pressure or vibration
• Helps maintain proper fluid flow by ensuring a tight seal

• One hose clamp

• Disconnect power and shut off water supply before servicing plumbing connections
• Use pliers or the appropriate clamp tool to expand and position the clamp; release slowly to seat it
• Replace any damaged or corroded hoses or fittings for a reliable repair

This top cover replaces a damaged or worn top panel to restore a clean, secure finish and protect internal components. It fits over the appliance frame and provides the mounting surface for control consoles and trim. What it does

• Covers and protects internal components from dust, debris and accidental contact
• Provides the correct mounting surface and alignment for control panels and trim pieces
• Restores cosmetic appearance when the existing top is dented, cracked or warped
• Helps prevent small items from falling into the cabinet through the top opening

• One top cover

• Disconnect power (and water if applicable) before beginning any work to avoid shock or injury
• Typical installation requires removing the control console or rear access panel to release mounting screws or clips
• Handle carefully to avoid scratching the painted surface; use appropriate fasteners and torque to avoid stripping

This suspension assembly supports the wash tub and absorbs vibration so your washer can run smoother and quieter. Replacing a worn suspension helps reduce shaking and banging and improves overall stability during spin.

• Supports and stabilizes the wash tub during wash and spin
• Absorbs vibration to reduce shaking, noise, and excessive movement
• Helps minimize out-of-balance interruptions and rebalance attempts
• Addresses symptoms such as banging during spin, excessive vibration, or a tub that sags/leans

• Disconnect power and water supply before servicing; wear gloves and eye protection
• Access the suspension from the cabinet/top as applicable and support the tub to prevent sudden drop
• Replace the assembly in the same location/orientation; ensure all connections are fully seated
• After installation, level the washer and run a test cycle to ensure smooth operation; many replace all suspensions as a set for balanced performance

The Drain Hose is an OEM part for LG washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle. The hose measures 67.5 inches in length.

Causes of a bad drain hose can include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM LG part is also compatible with Sears/Kenmore models.

This is a factory replacement parts assembly designed to restore proper fit and function of a specific component group in your appliance. Use it to replace a worn, damaged, or missing original assembly and maintain reliable operation. What it does:

• Provides a complete, preassembled component group specified by the manufacturer
• Restores proper alignment, support, and operation of the associated parts
• Helps resolve issues like looseness, rattling, misalignment, or intermittent function
• Direct-fit replacement engineered to match the original design

• One parts assembly

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Refer to your model's service documentation for the exact location and procedure
• Handle sharp edges and components carefully; wear cut-resistant gloves
• Verify correct operation before final reassembly

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This guide cover is a molded trim piece that shields and supports its mating guide/track, helping the assembly align and operate smoothly while protecting internal components from debris and damage.

• Protects the guide/track from wear and debris intrusion
• Helps maintain smooth alignment and operation of the moving assembly
• Can help resolve issues like rubbing, misalignment, or a loose/missing trim piece
• Restores a clean, finished look after damage or loss

• Unplug power and shut off water before servicing
• Compare the new cover to the original to confirm orientation
• Snap or screw into place per the unit's service manual; do not force
• Verify smooth travel and clearance after installation

The Lid Switch and Lock Assembly is an OEM component specifically designed for LG washing machines. It contains both the switch that detects when the lid is closed, as well as the metal lock mechanisms that securely engage the lid during active cycles. This switch contains a 47-inch wire harness with 6-pin plugs.

Symptoms of a bad lid switch and lock assembly include:

• The washer not starting or agitating with the lid open
• Inability to fully close or lock the washer lid
• Error codes related to sensed lid position issues

Causes of failure involve wear of lock moving parts combined with mechanical and electrical degradation over thousands of uses. Continuous hinge motions and detergent/cleaner exposure take their toll.

This Lid switch is also compatible with Kenmore units reliant on LG parts.

The Tub to Pump Hose Assembly is an OEM part for LG washing machines. This hose connects the tub to the drain pump, allowing water to be efficiently drained from the washing machine during the spin and drain cycles.

Over time, the hose can become clogged, develop cracks, or experience wear due to constant water flow and agitation. Damage can also occur from accidental mishandling or impact, leading to leaks or improper drainage.

Symptoms of a bad Tub to Pump Hose Assembly include:

• Water leaking from the washing machine
• Slow or incomplete drainage
• Error codes related to drainage issues
• Excess water remaining in the tub after the cycle

This OEM LG part is also compatible with Sears/Kenmore.

This bracket assembly secures internal components to the appliance frame, restoring stable support and alignment for panels or assemblies. Replacing a damaged bracket helps stop rattling and prevents misalignment that can affect operation. What it does:

• Provides a secure mounting point for panels, control boards, or internal assemblies
• Restores proper alignment to reduce vibration, noise, or rubbing parts
• Prevents loose components that can cause intermittent contact or wear
• Re-establishes structural support after impact, corrosion, or bracket failure

• One bracket assembly

• Verify power is disconnected before starting any repair
• Inspect mounting screws and adjacent parts; replace any damaged fasteners
• Tighten to manufacturer torque where specified and confirm proper alignment

This bracket assembly secures and supports internal appliance components, restoring proper alignment and stability to parts that have shifted or come loose. It provides a direct replacement to maintain safe, reliable operation. What it does:

• Provides a sturdy mounting point to keep panels, modules, or assemblies properly positioned
• Helps eliminate rattling, misalignment, or loose component movement
• Restores intended structural support after impact or wear
• Works as a direct-fit replacement to return original fit and function

• One bracket assembly

• Disconnect power (and water, if applicable) before beginning any repair
• Use appropriate tools and keep fasteners for a secure fit; replace damaged screws as needed
• Inspect surrounding components and wiring for damage before reassembly

The Detergent Box Assembly is an OEM part for LG washing machines. This part holds and dispenses detergent, fabric softener, and bleach at the appropriate times during the wash cycle, ensuring effective cleaning and care for your laundry.

Common causes of a bad detergent box include clogging or blockage from detergent residue, wear and tear from regular use, or damage to the dispenser mechanisms.

Symptoms of a bad Detergent Box Assembly include:

• Detergent, fabric softener, or bleach not dispensing properly
• Residue build-up in the detergent drawer
• Leaks or drips from the detergent box area
• Error codes related to detergent dispensing

This OEM LG part is also compatible with some Kenmore models.

This detergent box is the molded dispenser drawer that holds and releases liquid or powdered detergent into the wash tub during cycles, helping ensure detergent is delivered where needed for cleaning. What it does:

• Holds liquid or powdered detergent and channels it into the washer during the fill and wash cycles
• Helps prevent detergent from spilling into the cabinet or away from the wash water
• Common symptom of failure: detergent leaks, fails to dispense, or sits in the drawer instead of flowing into the tub

• One detergent box (dispenser drawer) as shown

• Remove power and water connections before accessing the dispenser area
• Inspect surrounding seals and mounting tabs; replace if damaged to ensure a proper fit
• Clean the dispenser area and rinse with water before installing the new box to remove residue

The Softener Cap is an OEM part for LG washing machines. It serves as the lid and housing for the internal water softener that prevents mineral deposits from building up. The softener cap funnels water to and from the softener compartment during various stages of the wash cycle.

Causes of a faulty softener cap can include cracked or degraded seals over extended usage, impact damage distorting fit, or harsh cleaners affecting plastics over time.

Symptoms of a bad softener cap include:

• Water leaks from around the softener area  
• The cap not closing or sealing properly 
• Mineral buildup occurring prematurely
• The softener not functioning as intended

This genuine LG replacement is compatible with Sears/Kenmore machines.

This softener dispenser cap replaces the worn or cracked cap that covers the fabric softener chamber, restoring proper containment and controlled release of liquid softener during the wash cycle. A simple, low-cost part that prevents leaks and keeps the dispenser functioning. What it does

• Covers and seals the fabric softener compartment so liquid stays in the dispenser until the rinse cycle.
• Helps prevent softener from leaking into the washer drum between cycles.
• Restores a secure fit when the original cap is cracked, warped, or missing.
• Resolves issues with softener dispensing at the wrong time or pooling in the dispenser.

• One softener dispenser cap (1 piece)

• Disconnect power to the washer before accessing internal parts and follow all safety precautions.
• Typically accessed by removing the dispenser drawer or top panel—refer to your washer's service instructions.
• Inspect surrounding dispenser components for damage and replace any worn parts to ensure a proper seal.
• No electrical connections; basic hand tools may be required.

This replacement nozzle assembly restores proper flow and distribution within the appliance's system to maintain cleaning performance. Replace a cracked, clogged, or worn nozzle to help prevent performance loss and keep the unit operating efficiently.

• Directs and concentrates flow through the appliance for effective operation
• Helps maintain a sealed path to avoid leaks or loss of performance
• Damage or obstructions can cause reduced cleaning results, unusual noise, or visible leaks/air leaks
• Visible cracks, warping, or a loose connection indicate the nozzle should be replaced

• Disconnect power (and water supply if applicable) before servicing
• Remove the old nozzle per your model's service information; clear any debris from the mating areas
• Inspect related seals/gaskets and replace if worn to ensure a proper seal
• Install the new nozzle securely and test for proper operation and leaks/airflow

The Housing Assembly, Clutch is an OEM part for LG washing machines. It is integral to the washing machine's transmission system, helping to engage and disengage the tub during wash and spin cycles.

You should replace this clutch housing assembly if it becomes worn out or damaged. Over time, the clutch can wear out due to repeated use, heavy loads, or poor maintenance. Additionally, debris or foreign objects can cause damage to the housing or internal components.

Symptoms of a bad clutch housing assembly include:

• Washing machine not spinning or agitating properly
• Excessive noise during wash or spin cycles
• The washer not completing cycles or stopping mid-cycle

This OEM LG part is also compatible with Sears/Kenmore models.

The Water Inlet Valve is an OEM replacement part specific to LG washing machines. It is an electronic solenoid valve located near the water supply inlet ports that controls the flow of water into the washer tub. The inlet valve precisely regulates water levels during different phases like filling, washing, rinsing, and spinning cycles.

Causes of a bad water inlet valve can include worn or faulty electronic components, mineral buildup obstructing valve movement, or damage to seals and diaphragms.

Symptoms of a bad water inlet valve include:

• Inability to properly fill the washer tub during cycles
• Water leaking or flooding from the valve area
• Erratic water temperature or varying fill levels between loads
• Cycles failing to advance due to inadequate or unregulated water flow

This OEM LG part is also compatible with Sears/Kenmore models.

The Hose Connector is an OEM part for LG washing machines. It controls the water flow during the wash and rinse cycles. This part is designed to facilitate a secure and leak-proof connection between different sections of the washing machine, such as the inlet valve and the tub, or the pump and the drain hose. Ensuring these connections are secure is vital for the efficient operation of the washing machine, preventing leaks and maintaining optimal water usage.

Causes of failure may involve cracks, splitting, or collapsed seals/gaskets, as well as excessive mineral or foreign deposits that can obstruct water flow.

Symptoms of a bad hose connector are:

• Slow or incomplete filling during wash cycles
• Water leaks at the supply valve or connector area
• Connector split, cracked or compromised fittings

This genuine LG replacement is also compatible with Kenmore washing machines.

This inlet hose channels household water into the appliance during the fill cycle. Replacing a cracked, brittle, or leaking hose restores a secure, leak-resistant path that helps prevent puddles and fill-related interruptions. What it does:

• Routes incoming water from the inlet valve into the appliance's internal water path
• Helps maintain a watertight connection when properly secured with clamps
• Typical failure signs: dripping or puddling under the unit, visible cracks/kinks/bulges, or lingering dampness
• A restricted or leaking hose can contribute to long fill times or incomplete cycles

• 1 inlet hose

• Disconnect power and turn off the water supply before servicing
• Place towels or a shallow pan to catch residual water
• Note the original routing and clamp locations; install the new hose the same way without twists or kinks
• Fully seat hose ends and secure clamps; restore water and run a brief fill to check for leaks

Detergent housing assembly that holds and routes detergent to the washer dispenser, helping ensure proper detergent flow and reducing leaks or dispenser jams. Fits into the dispenser area to replace cracked, warped, or damaged housing components. What it does:

• Houses and channels liquid or powdered detergent into the dispenser and wash chamber
• Restores proper detergent release when the original housing is cracked, broken, or warped
• Helps stop leaks and detergent buildup around the dispenser area
• Works with the dispenser drawer and related seals to maintain correct flow

• Disconnect power and turn off the water supply before starting service
• Use basic hand tools and follow the washer service manual or OEM diagram for disassembly/reassembly
• Inspect and replace any worn seals or gaskets at reassembly to prevent leaks

The Stator Assembly is an OEM replacement part for LG washing machines. It is an electrical component inside the motor that converts rotational motion to electrical energy to power spinning motions.  Note: For the RPS or Hall Sensor, order part number AP7015078.

Symptoms of a faulty stator include:

• Slow or inefficient spinning, rubbing noises  
• The machine failing to fully drain or spin clothes
• Repeated blowouts or failure of related motor components

Causes can be wear and tear over extended use. Environmental factors like dust and moisture exposure may degrade insulation integrity. 

This OEM stator is also compatible with some Kenmore front-load washer models.

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

This rotor assembly is the rotating half of the direct-drive motor in your washer. It mates with the stator to spin and agitate the basket, restoring drive when the original rotor is worn, cracked, or stripped.

• Forms the magnetic rotor of the direct-drive motor to turn the wash basket
• Transfers motor torque directly to the tub for spin and wash action
• Common symptoms: no spin or agitation, starts then stops, loud grinding/clicking, motor-related error
• Visible damage may include cracked hub, stripped splines, or loose fit on the shaft

• Disconnect power and water; wear gloves and eye protection
• Access from the rear, remove the back panel, hold the basket, then remove the center bolt and pull the rotor straight off (strong magnets)
• Align splines/keyway, seat the rotor fully, and reinstall/tighten the center bolt securely
• Inspect the stator and hall sensor for damage before reassembly and test a spin cycle

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

The Clutch Motor is an OEM part for LG washing machines. This motor engages the clutch mechanism, allowing the washer to switch between agitating and spinning cycles effectively.

Causes of a bad clutch motor can include wear and tear over time, electrical issues, or mechanical failure due to overloading or improper use.

Symptoms of a bad clutch motor include:

• The washer not agitating or spinning
• Unusual noises during the wash or spin cycles
• The drum not rotating properly
• The washer stopping mid-cycle

This OEM LG part is also compatible with Sears/Kenmore models.

This filter assembly is the refrigerator water filter housing that holds and secures the replaceable water filter cartridge, helping deliver clean-tasting water and proper flow to the dispenser and icemaker. Designed to match OEM fit and function. What it does:

• Houses the water filter cartridge so water is processed before reaching the dispenser and icemaker
• Restores proper water flow when a damaged or cracked housing restricts supply
• Helps prevent contaminants and odors from passing through the system when used with the correct filter cartridge
• Supports reliable sealing to reduce risk of leaks at the filter connection

• One filter assembly housing

• Turn off refrigerator water supply and dispense any remaining water before beginning work
• Replace only with the correct OEM housing and compatible filter cartridge for this unit
• Inspect O-rings/seals and replace if worn to ensure a watertight fit

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

This is a small OEM washer used with the washer's internal mounting hardware to provide proper spacing and secure fasteners. It helps keep assemblies aligned and prevents hardware from loosening during operation. What it does:

• Acts as a spacer and load distributor for bolts or screws in the washer assembly
• Helps maintain proper alignment of panels or components
• Reduces wear between mating metal parts
• Can prevent fasteners from backing out due to vibration

• One washer as pictured

• Always unplug the appliance and shut off the water supply before servicing
• Access the mounting location per the service manual or parts diagram; replace only like-for-like
• Install with the correct orientation and hardware; do not overtighten fasteners
• If other fasteners or parts are corroded or worn, replace them at the same time

Kit is no longer available. Order MCJ61861201 and ACP72929002 separately.

The Coupling Washer is a genuine OEM part for LG washing machines. As a crucial component connecting the drive motor to the inner drum, the coupling washer allows for the transmission of rotational force during the spin cycle. This rotational movement generated by the drive motor is what extracts water from clothing, effectively drying clothes. 

Symptoms of a bad coupling washer include:

• The washing machine fails to spin or rotates very slowly
• Vibrations and noise during spinning
• Rubber couplings tearing or shredding prematurely

Over time, the constant exposure to vibrations and forces during spin cycles can cause the rubber material of the coupling washer to deteriorate. 

This OEM LG part is also compatible with Sears/Kenmore washers.

This dispenser assembly is the washer's detergent drawer housing. It channels incoming water through the detergent and fabric softener compartments (and prewash, if equipped) so additives are dispensed at the correct time and helps prevent leaks at the dispenser area.

• Directs water through the dispenser to flush detergent/softener into the tub at the proper points in the cycle
• Replaces cracked, warped, or clogged housings that leak or misdirect water
• Helps resolve detergent or softener remaining in the drawer after a cycle
• Addresses water leaking or overflowing from the dispenser area or visible damage/mineral buildup in the dispenser box

• Unplug the washer and shut off water supplies before servicing
• Pull out the drawer, remove the top cover as needed, then remove mounting screws and release hose clamps to detach the old assembly
• Move hoses/clamps to the new assembly and ensure gaskets/siphon caps are properly seated
• Run a quick fill/rinse to check for leaks before final reassembly

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This small cover cap conceals an exposed fastener or opening on your appliance, restoring a clean, finished look. It also helps protect the area from dust and splashes for a tidy, long-lasting installation.

• Covers and protects an open screw hole or attachment point on a panel or door
• Restores a clean, factory appearance
• Helps keep dust and moisture out of the opening
• Common signs it's needed: missing cap, cracked/broken cap, loose cap, won't stay clipped

• Disconnect power (and water, if applicable) before servicing exterior panels or doors
• Note the cap's orientation and any retaining tabs before removal
• Use a plastic pry tool to gently release the old cap; press the new cap until fully seated
• Avoid forcing the cap or overtightening any underlying fastener to prevent damage

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.