Parts for Kenmore 417.90862991 (41790862991, 417 90862991): Panel Parts

Access panel for washer dryer combo units. Covers internal components and provides service entry. Replace if cracked, broken, or missing. Installs on exterior.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Top panel for laundry center units. Covers and protects the upper surface. Replace if cracked, chipped, discolored, or damaged from wear and tear.

Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.

For a complete drum bearing and shaft kit order 5303281153.

Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Front Felt Glide Assembly is an OEM part for Frigidaire dryers. This part allows smooth operation of the dryer drum, providing a felt pad that the drum glides on as it rotates. This not only helps to support the drum but also minimizes friction and noise, contributing to the efficient and quiet operation of the dryer. 

Over time, the felt portion of the glide assembly can wear down, leading to increased friction between the drum and the dryer's front panel.  

Symptoms of a bad Front Felt Glide Assembly include:

• Unusual noises during operation, such as squeaking or grinding
• The dryer drum may catch or hesitate during rotation
• Increased wear and tear on clothing due to the drum's rough movement
• The dryer may take longer to dry clothes efficiently due to the drum's impaired rotation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replaces a worn, dented, or rusted dryer drum to restore smooth tumbling. Galvanized back construction. Ensures clothes move and dry evenly inside.

The Lower Front Felt Seal is an OEM part for Frigidaire dryers. This seal prevents hot air from escaping the dryer drum, ensuring optimal drying efficiency and preventing heat loss. It also helps reduce noise and vibration during operation.

Causes of a faulty lower front felt seal can include wear and tear over time, damage from foreign objects or excessive heat, or adhesive failure. These factors can result in air leakage, increased drying time, or excessive lint buildup.

Symptoms of a front felt seal may include:

• Air leakage around the dryer door or front panel
• Excessive lint accumulation near the dryer opening
• Unusual noises or vibrations during the operation

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Note: For the Hi-Temp Adhesive, order part number 5308027429. Additional parts to check are the rear drum bearing kit 5303281153 and the front felt glide assembly 5303937139.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

Traps lint and debris during drying to prevent vent clogs and maintain efficiency. Replace when torn, rusted, or bent. Verify fit with your model.

Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Supports the rear of your dryer drum for smooth, even rotation. Replace if drum wobbles, makes noise, or doesn't turn properly. Verify fit by model number.

This safety thermostat is a temperature-sensitive switch that helps protect your appliance from overheating. When excessive heat is detected, it opens the circuit to stop power to critical components, helping prevent damage and ensuring safe operation.

• Monitors temperature at a specific location and interrupts power if it exceeds a safe limit
• Can cause no power, no heat, or shutdown during use when failed or tripped
• Helps prevent overheating damage to internal components
• Restores normal operation when replaced

• Disconnect power to the appliance before service
• Note wire positions and terminal orientation before removal
• Use proper tools and avoid bending or stressing terminals
• After installation, check for underlying overheating causes (blocked airflow, failed fan, etc.)

Replacement control panel console for laundry center front assembly. Restores appearance and provides mounting surface for user controls. Replaces cracked, faded, or damaged console.

Secures the dryer door to the cabinet and provides a smooth pivot point. Replace this hinge if bent, worn, or broken to restore proper door alignment.

Mounting screw secures panels, trim, or brackets in dryers, washers, and ranges. Replace lost, stripped, or corroded screws to restore stability.

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

White door handle for laundry center dryer door. Replaces cracked, loose, or missing handles. Restores secure grip for opening and closing the door.

Door panel for laundry center units. Replaces cracked, damaged, or discolored exterior panels. Restores clean appearance to front-loading door assembly.

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

Electrical harness for washer dryer combos. Connects internal components to power supply. Replace if wires are frayed, damaged, or connectors are broken.

Replacement drying rack for washer dryer combo units. Installs inside drum for air-drying delicate items. Order a new rack if yours is cracked or missing.

Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Trim strip with adhesive tape for washer dryer combo units. Replaces cracked, peeling, or missing decorative trim along control panel edges.

Printed owner's manual for washer dryer combos. Includes operation instructions, care guidelines, and troubleshooting tips. Replace lost or damaged guides.

Cushion bumper for washer dryer combo units. Installs to absorb vibration and reduce noise. Replace if cracked, worn, or missing for proper support.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Secures the drain hose to prevent leaks and disconnection during spin cycles. Replace if cracked, loose, or causing water leakage. Verify fit with your model.

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

Vertical spring adjuster insert.

Converts compatible gas dryers from natural gas to propane. Includes orifices and components for safe LP operation. Order if switching fuel types.

Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.