Range / Cooktop / Oven Burner & Related Parts

This replacement burner cap sits on a gas range surface burner to protect the burner head and help direct the flame for more even heating. Use it to replace a cracked, chipped, or missing cap and restore stable burner performance. What it does:

• Covers the burner head to help shape and stabilize the gas flame for consistent cooking.
• Promotes even heat distribution across cookware by centering the flame.
• Keeps spills and food debris off burner ports for easier cleaning and more reliable ignition.
• Replace when cap is cracked, chipped, displaced, or causing uneven or yellowish/erratic flames.

• Make sure the range is turned off and fully cooled before handling burners.
• Remove the grate, lift the old cap straight off, and seat the new cap flat and centered on the burner head — no tools typically required.
• If the cap does not sit flush, clean the burner head of debris before reinstalling; do not force the cap.

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

Approx 2-1/2 inches in diameter

This head burner main is the primary gas burner head used on compatible gas ranges to direct and distribute the flame for proper cooking. It replaces a damaged or corroded burner head to restore even heating performance. What it does:

• Directs gas to the cooktop for ignition and controlled flame distribution
• Helps maintain even heat across the cooking surface for consistent results
• Can resolve symptoms like uneven flame, visible damage, or poor ignition at the burner
• Works with the burner cap and valve assembly as part of the burner system

• Turn off gas supply and power to the appliance before starting any work
• Remove grates and burner caps to access the burner; follow OEM disassembly guidance
• Replace only with the exact part number to ensure proper fit and function

18K Simmer

This surface burner cap is a genuine General Electric part, sold individually. It can be used as a replacement part for a gas range. This surface burner cap provides a covering for the burner of the gas range so that the infrastructure of the burner and the ignition are not damaged in the process of utilizing the burners.A surface burner cap might have to be replaced if it is lost, misplaced, or has suffered damage that prevents the component from protecting the burner and the ignition. Damage can include punctures, cracks, chips, or erosion to the material that weakens the ability of the component to protect the burner and ignition. If this damage occurs, the component should be removed and replaced by this genuine OEM replacement part. It is a simple replacement process that will require no special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This surface burner cap is compatible with General Electric brand gas ranges.

This burner cap sits on top of the surface burner head to shape the flame and shield the head from spills. Replacing a damaged or missing cap helps restore even heating, reliable ignition, and the cooktop's original appearance.

• Covers the burner head and disperses flame for more even cooking
• Protects burner head and ports from food and liquid spills
• Helps maintain proper ignition and a steady blue flame
• Helps with symptoms like uneven/yellow flame, delayed ignition, or poor simmer

• Allow the cooktop to cool completely before handling
• Disconnect power and shut off gas
• Clean the burner head and clear ports before seating the cap
• Center the cap so it sits level and flush; misalignment can affect ignition and flame

The Regulator is an OEM replacement part for Whirlpool ranges. It is responsible for controlling the flow of gas to the burners and ensuring the proper gas pressure for efficient and safe cooking.

A bad pressure regulator can occur due to wear and tear, clogs, or damage to the internal components. If you notice symptoms such as weak or inconsistent flame, gas leaks, or difficulty in igniting the burners, it may indicate a faulty valve and pressure regulator.

Symptoms of a bad regulator include:

• Weak or inconsistent flame
• Gas leaks
• Difficulty in igniting the burners

Restore your range by replacing the faulty or damaged valve and pressure regulator with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This surface burner cap sits atop the gas burner head to distribute flame evenly and protect the burner from spills, helping restore steady flames and reliable ignition when the original cap is worn, warped, or missing.

• Distributes flame for more even heating across cookware
• Shields the burner head from boil-overs and debris
• Supports proper ignition when correctly seated and level
• Common signs it's needed: missing cap, chips/cracks, warping, uneven or yellow flames

• Allow the cooktop to cool completely; shut off gas/power if performing additional service
• Remove the grate, lift off the old cap, and clean the burner head surface
• Center the new cap on the burner head so it sits flat and does not rock
• Test the burner; if ignition is delayed or flames are uneven, reseat the cap

Replacement oven burner that restores heat in the oven's bake chamber so you can cook evenly. Installs in place of a damaged or worn burner to help the oven reach and maintain proper cooking temperatures. What it does:

• Produces the primary bake heat for the oven cavity.
• Replaces a cracked, corroded, or non-functioning burner that may cause weak or no heat.
• Helps correct uneven baking or failure to reach set temperatures when the burner is the source of the problem.

• Disconnect electrical power and shut off the gas supply before beginning work; follow all local codes.
• Use appropriate hand tools and avoid forcing parts; inspect sealing surfaces and connections for damage.
• If gas fittings or ignitors are involved, test for leaks after installation.

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

The Burner Head is an OEM component specifically designed for Whirlpool gas ranges. Located beneath each cooking surface, it allows precise flame control and heat delivery for safe food preparation.

Causes can be related to accumulated food or mineral deposits distorting gas/air mixing pathways. Normal aging effects like rusting also impact burner functionality.

Symptoms of a bad burner head include:

• Flames appear unusually high, low, or unstable
• Uneven cooking results occur on burner surfaces  
• Singeing or burning odors develop during use
• Any ports that appear collapsed or restricted

This OEM Whirlpool replacement burner head restores consistent heat levels. Installed promptly to repair scorches or damage, it prevents continued surface and connection deteriorations to the manifold. 

Compatible also with some GE and Frigidaire ranges, this part ensures safe, dependable cooking control.

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

Black. C Burner

Replacement snap-on cap that restores a finished appearance and helps protect underlying components from dirt and accidental contact. Fits original mounting locations to cover exposed hardware and improve appliance safety and aesthetics. What it does:

• Covers and protects exposed hardware, terminals or posts to reduce debris buildup and accidental contact.
• Restores a clean, finished look to panels, trim or appliance edges.
• Helps reduce rattling or vibration noise caused by missing trim pieces.
• Use when the original cap is cracked, broken, missing or when exposed fasteners are visible.

• Always disconnect power (and water, if applicable) before attempting any repair.
• Remove the damaged cap by hand or with a small pry tool; press the replacement cap onto the mounting post until fully seated.
• Avoid excessive force during removal/installation to prevent damage to the mounting post or surrounding trim.
• If mounting posts or clips are damaged, replace those components to ensure a secure fit.