Range / Cooktop / Oven Burner & Related Parts

This valve controls gas flow to a range/cooktop surface burner for smooth ignition and precise flame adjustment. Replacing a worn valve helps restore reliable burner lighting, accurate heat control, and safer shutoff.

• Regulates gas to a surface burner for ignition and flame size control
• Sticking or worn internal seals can cause hard-to-turn operation or gas odor
• Failure may prevent the burner from lighting or shutting off completely
• Inconsistent or unresponsive flame adjustment can indicate a failing valve

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; access the valve/manifold per your model's instructions
• Mark and disconnect tubing and any wires; transfer fittings or a separate spark switch from the old valve if applicable
• After installation, restore gas and check all joints with an approved leak-detection solution; verify proper burner operation

Note: Includes ignitor

This burner replaces a worn or damaged unit on your range to restore reliable, even heat. Swap it in to correct poor performance caused by cracks, corrosion, or blockages so cooking results return to normal.

• Provides the heat source for a cooking zone on the range
• Common fix for damage, warping, or clogged ports/passages
• Symptoms include won't light/heat, weak or uneven heating, or irregular/yellow flame on gas models
• Visible rust, cracks, or deformation indicate replacement is needed

• Disconnect power; for gas models, also shut off the gas supply. Allow the appliance to cool completely
• Remove grate/cap or unplug element as applicable; take out screws/retainers to lift off the old burner
• Transfer reusable items from the original part (such as cap, electrode/igniter, and screws) if required by your model
• Align correctly and tighten fasteners evenly; restore utilities and test for proper operation

The Top Burner is an OEM part for Frigidaire ranges. This burner is designed to provide a reliable flame for cooking on the stovetop. It ensures consistent heating and efficient cooking performance, fitting seamlessly into the design of your range.

Common causes of a bad burner include clogging from food spills, corrosion due to exposure to moisture, or physical damage from heavy cookware.

Symptoms of a bad top burner include:

• Uneven heating or inconsistent flame
• The burner not igniting properly
• Visible damage or corrosion on the burner
• A weak or flickering flame

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Whirlpool orifice holder is an OEM replacement part responsible for regulating the flow of gas to the surface burners of the cooktop. This part ensures the safe delivery of gas to the burner, allowing for controlled ignition and heat generation. The orifice holder is located beneath the burner assembly, and it connects to the gas supply line. It contains the orifice, which is a small opening that determines the gas flow rate to the burner.

Causes of a bad holder-orifice can include wear and tear over time, exposure to high temperatures, or accidental damage during maintenance or cleaning. When the holder-orifice becomes compromised, it can lead to issues with gas flow and burner efficiency, impacting the overall performance of the oven.

Symptoms of a bad Holder-Orifice include:

• Uneven heating or burner performance
• Weak or inconsistent flame
• Gas smell near the burner area
• The burner not igniting properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This central burner cap covers the center of a gas burner to shape the flame and protect the burner head. Replacing a worn or missing cap restores proper ignition, even flame, and clean cooktop performance.

• Directs the center flame for more even heat distribution
• Shields the burner head/igniter area from spills and drafts
• Helps ensure consistent ignition when properly seated
• Common symptoms: uneven or yellow flames, delayed ignition, sooting, or a chipped/warped cap

• Turn all burner controls off and let the surface cool completely
• Lift off the old cap; clean and dry the burner head surface
• Center the new cap on the burner head so it sits flat with no rocking or gaps
• Test the burner; if the flame is uneven or lifting, re-seat the cap until level

This LP Conversion Kit is an OEM replacement part for Whirlpool gas ranges and wall ovens. It allows you to convert the range from using natural gas to liquid propane (LP) gas. This kit includes orifices that fit over the burner valves.

Natural gas and LP gas have different combustion properties, such as different pressure requirements and gas flow rates. Therefore, using the incorrect orifices on your gas range can lead to dangerous situations, including fires, burns, or even explosions.

If you want to convert your Whirlpool gas range from natural gas to LP gas, it is important to use the correct conversion kit designed for your range's make and model. Attempting to modify or alter the gas flow without the correct parts is extremely dangerous and should not be attempted.

The Burner Cap is an OEM replacement part for Whirlpool gas ranges. This small part sits atop the gas burner on the left and right front to help direct flames from the jet and provide an even spread for efficient heating. Color: Black

Causes can be normal wear over time from cooking usage, as well as accidental objects left on burners that cause impact damages.

Symptoms of a damaged or worn burner cap include:

• uneven cooking temperatures
• flames that appear too high or inconsistent
• potential burner flashback or fire hazards if portions are cracked or missing.

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This is the outer burner cap for a sealed gas burner. It covers the burner's outer ring to shape a steady flame, protect the burner head from spills, and help ensure consistent ignition and even cooking results.

• Shapes and distributes the flame around the outer ring for balanced heating
• Promotes reliable ignition when properly centered and seated
• Shields burner head and ports from spills and debris that can affect performance
• Replace if the cap is chipped, warped, or missing; symptoms can include yellow/uneven flames, sooting, or repeated clicking/delayed ignition

• Disconnect power and allow the cooktop/range to cool before servicing
• Lift off the old cap; clean the burner head and seating surface
• Position the new cap flat and centered; it should sit level and not rock
• Light the burner to verify a steady, blue flame; reposition if needed

The LP Bake and Broil Kit is an OEM replacement part for Whirlpool ranges. It is a kit containing everything needed to convert the oven from Natural gas to LP.

Causes of a bad bake/broil system can include cracks, leaks, or corrosion in gas lines that produce unsafe flames over time. Pilot lights may fail to light consistently.

Symptoms of failures include:

• Inability to ignite bake/broil burners
• Erratic or intermittent baking temperatures
• Uneven cooking due to improper burner positioning
• Strong gas or chemical smells from the oven

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The LP Orifice Kit is an OEM part for Whirlpool gas ranges. It contains a set of five orifices designed specifically for use with liquid propane (LP) gas. Note: For the oven orifices, on some models they are adjustable and some they are not. Refer to parts list for your model when oven orifices are needed. LP orifice kit includes 5 orifices.

Causes of a bad LP Orifice Kit may stem from incorrect orifice size for the specific LP gas supply, wear or damage to the orifices over time, or improper installation.

Symptoms of needing to replace the LP Orifice Kit can include:

• Uneven heating or incomplete combustion of the burners
• Yellow or flickering flames instead of a steady blue flame
• Reduced cooking performance or inefficient heating

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Cap-Burner is an OEM replacement part for Frigidaire cooktops and ranges. It is a crucial component that covers and protects the gas burner assembly, while also distributing the flame evenly for optimal cooking performance.

Symptoms of a bad Cap-Burner:

• Uneven or irregular flame patterns 
• Difficulty in igniting or maintaining a steady flame
• Discoloration or warping of the cap due to excessive heat exposure
• Clogged or obstructed gas flow, leading to poor burner performance

Causes of a defective Cap-Burner can include prolonged exposure to high temperatures, impact damage, or general wear and tear over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore cooktops and ranges.

The Cap-Burner (Black) is an OEM part for Whirlpool gas ranges and cooktops. This burner cap sits on top of the right rear burner head and helps distribute the flame evenly for efficient cooking. It also protects the burner head from spills and debris, ensuring proper functionality and longevity of the burner.

Over time, burner caps can become damaged or worn out due to constant exposure to high temperatures, spills, and regular cleaning. A bad burner cap can lead to uneven flames, poor cooking performance, and potential damage to the burner head.

Symptoms of a bad burner cap include:

• Uneven or irregular flame
• Flames that are too high or too low
• Difficulty igniting the burner
• Visible cracks or discoloration on the cap

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Oven Bake Burner with Spark Igniter is an OEM part for Whirlpool ovens. This component is essential for igniting the gas in the oven, allowing it to produce the necessary heat for baking.

Please note: The igniter is only available with this kit and not separately.

You should replace the oven bake burner with spark igniter if it becomes defective. Causes of a bad bake burner or igniter can include wear and tear from regular use, exposure to high temperatures, or damage from food spills and debris. Electrical issues or a malfunctioning igniter can also lead to failure.

Symptoms of a bad oven bake burner with spark igniter include:

• The oven not heating up or taking a long time to reach the desired temperature
• Uneven baking or inconsistent cooking results
• The igniter not sparking or clicking
• Gas smell without ignition indicating the igniter is not working properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Range Burner Cap is an essential component for maintaining the efficiency and safety of your range. Designed specifically for Samsung ranges, this genuine OEM part ensures a perfect fit and seamless integration with your appliance. The burner cap helps distribute heat evenly across the cooking surface, providing consistent performance for all your culinary needs. Made from high-quality materials, it is built to withstand daily use, reducing the likelihood of wear and tear. Replacing a damaged or worn burner cap with this genuine OEM part not only restores your rangeGÇÖs functionality but also enhances its overall performance. Easy to install, the Range Burner Cap allows you to quickly get back to cooking without the need for professional assistance. By choosing this reliable replacement part, you ensure that your Samsung range operates smoothly and efficiently, offering you a dependable cooking experience every time.

The Burner Cap Kit is an OEM replacement part for Whirlpool ranges. It is a kit that contains replacement burner caps for the range's gas burners. These burner caps play a vital role in distributing heat evenly across pots and pans placed on the gas burners. Color: Grey. Kit includes five burner caps. For the burner cap kit in black use part number WPW10183374.

Causes of a bad burner cap kit include wear and tear over time from heat exposure, accidental damage from pots and pans, or issues with the mounting hardware that secures the caps.

Symptoms of bad burner caps can include:

• Uneven or inefficient heating from the burners
• Discolored, cracked, or missing burner caps
• Flames not contained within burner cap openings
• Over extensive use, burner caps can deteriorate or become misshapen. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.