Range / Cooktop / Oven Switch

A replacement door switch that lets the appliance detect door open/close and enables normal operation and lighting. Restores reliable door sensing so cycles start and interior lights respond when the door opens. What it does:

• Detects when the door is opened or closed so the appliance can start or stop cycles safely
• Enables or disables the interior light based on door position
• Commonly replaces a faulty or intermittent switch that prevents the unit from starting or the light from working
• Simple electrical/mechanical switching — designed to match original function

• Disconnect power before inspecting or replacing the switch to avoid shock risk
• Access may require removing the control panel or inner door trim depending on model
• Handle the switch and connectors carefully to avoid damaging terminals or wiring

This is an electrical relay used in ranges and ovens to control power to heating elements or other components. It acts as a switch that opens or closes a circuit in response to signals from the control board. Replace this relay if your oven or burner fails to heat, heats intermittently, or stays on continuously.

This door switch interlock assembly is the door latch switch that detects and secures the dishwasher door so cycles can start and run safely. It restores proper door sensing and locking for normal operation. What it does:

• Detects when the dishwasher door is fully closed so the control will allow a wash cycle to start.
• Locks or interlocks the door during operation to prevent accidental opening and stop leaks.
• Helps resolve symptoms such as the dishwasher not starting, control lights flashing, or cycles stopping when the door is closed.
• Works as the electrical/mechanical interface between the door and the appliance control.

• One door switch interlock assembly

• Disconnect power to the appliance (unplug or shut off breaker) before beginning repair.
• Remove the dishwasher door panel or access panels as required to reach the latch; keep screws/fasteners organized.
• Align and secure the new interlock assembly and test door engagement and cycle start before reassembly.

This rotary selector switch lets the appliance select between functions or cycles by turning the control to the desired setting. It restores reliable, tactile selection and stable electrical contact for normal operation. What it does:

• Provides a rotary contact point to change modes, cycles or heat/cool settings
• Re-establishes reliable electrical connection when worn or intermittent switching causes erratic operation
• Stops slipping, sticking, or loss of detents that prevent proper selection
• Helps resolve no-response or incorrect-function symptoms when the control is turned

• One selector switch

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removing the console or control panel—keep fasteners and hardware organized
• Handle contacts and terminals carefully; avoid bending or contaminating connections
• Test operation after reassembly

This rack sensor switch assembly detects rack position and completes the electrical connection needed for proper operation of the appliance's rack-related functions. Replaces a worn or damaged switch to restore reliable rack sensing. What it does:

• Acts as the rack-position sensor/switch that signals the control when the rack is in place
• Restores intermittent or failed rack-detection that can interrupt related functions
• Helps prevent control errors or unexpected behavior caused by a faulty switch
• Commonly replaced when the switch is cracked, corroded, or unresponsive

• One rack sensor switch assembly

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle with care to avoid damaging the connector or surrounding components
• Basic hand tools may be required; access instructions available

This wiring harness assembly routes power and signals between the appliance control and electrical components so the unit operates reliably. It replaces a damaged or burnt harness to restore proper electrical connections and reduce intermittent faults. What it does:

• Connects controls, switches and motors to the main power and control board
• Restores interrupted circuits that can cause intermittent operation or component failure
• Helps resolve symptoms like lights, fans or motors not running or responding
• Replaces frayed, melted or corroded wiring that creates shorts or open circuits

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle connectors by the plug bodies; avoid pulling on wires
• Route and fasten the harness exactly as the original to prevent chafing or heat exposure

This is a latching switch that detects whether the microwave door is properly closed and secured. It is part of the door interlock safety system that prevents the microwave from operating when the door is open. Replace this switch if the microwave does not start, runs with the door open, or blows a fuse when the door is closed.

If your cooktop burners won't ignite or spark continuously, the igniter switch may need replacement. This part controls spark ignition timing.

This door switch detects when the appliance door is closed and signals the control so the unit can start or run. Replacing a faulty switch restores proper door-sensing and safe operation. What it does:

• Detects door open/closed status and sends the signal to the appliance control
• Prevents the unit from starting or running if the door is open
• Commonly linked to symptoms like the appliance not starting, not completing cycles, or lights/controls behaving incorrectly
• Works as the safety interlock for door-dependent functions

• One door switch

• Disconnect power before servicing to avoid shock or injury
• Match connector style and mounting alignment to the original switch before final installation
• Handle the switch and wiring gently to avoid damage to terminals or harnesses

Color: Black