Need Help?
Call
Fix burners that won't light or spark in the wrong place with this igniter electrode. Requires removing cooktop top—patience needed for many screws.
Removed the top and replaced 2 of the electrodes. Read more
Fix a range that won't turn on, shows flashing clock, or displays F1E0 error code. This electronic control board manages all burner and oven functions.
I ordered the part and repaired it myself. I am a 67yr old widow. Read more
The Bake Element is an OEM component for Frigidaire wall ovens. It is an integrated heating coil that generates heat through electric resistance when powered. Located near the bottom of the oven cavity, the bake element facilitates heating for various cooking functions like baking, roasting, or warming. This element measures approximately 13 x 11 inches. Symptoms of a bad bake element include:
Causes can be cracks in ceramic sheathing allowing arcing, or mineral deposits coating coils over extended use impeding heat transfer.
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
First, I took an ohm reading across the elements and determined the bad one, which was failed, open circuit. (Zero continuity) I then replaced the lower heating element of the upper oven. Although the design of the oven and element make it appear that it will just drop down and slide out the front, this is not quite the case. There is not enough clearance for it to drop all the way down. You have to pull the entire double-oven unit out of the wall, separate the upper and lower halves a few... Read more
Replace cracked, rusted, or stained 8-inch drip pans under coil burners on electric ranges and cooktops. Catches spills and protects cooktop surface.
With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more
The Door Handle is an OEM part for Frigidaire ovens. It is designed to provide a secure grip for opening and closing the oven door. This handle is white in color and 29" in length. Please note, the mounting screws are not included with the handle.
You should replace the door handle if it becomes loose, damaged, or broken. Causes of a bad door handle can include regular wear and tear from frequent use, exposure to high temperatures, or accidental impacts that cause cracks or breaks. Over time, these issues can make the handle less effective or unsafe to use.
Symptoms of a bad door handle include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
We ordered a new handle and two screws. The part was very easy to find and was in stock. Shipped out in 2 days and delivered by fed -ex. My teenage son put the handle on in less than 5 minutes. very easy. So happy we can finally use the oven again. Read more
Oven won't heat or bakes unevenly? The bake element likely failed. Simple DIY fix—just remove two screws, disconnect wires, and install new element.
I purchased a new elelmnt and fixed it myself!! Read more
Seals your oven door to prevent heat loss and maintain cooking temperatures. Replace if worn, cracked, or heat escapes. Confirm fit with your model.
Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more
This 8 inch drip pan installs under coil burners to catch spills and protect your cooktop. Replace cracked, rusted, or heavily stained pans to restore appearance.
$4 part and a little time saved $250 if I had had to replace the whole plug-in duel burner unit for our Jenn-Air range. Spade that was replaced fed both burners, other two spades just one. If your burners do not turn on, check the spades before you replace the coils. Read more
Oven won't heat or bakes unevenly? A faulty bake element is often the cause. This bottom heating element restores even baking. DIY install in 5-10 minutes.
Repair video was very helpful. Followed the instructions and the element was replaced easily and correctly. Read more
Oven won't heat to the right temperature or overheats? This electric range thermostat monitors and regulates oven temperature for consistent cooking results.
Oven rack for electric ranges. Slides into oven cavity to hold cookware during baking. Replace if cracked, bent, warped, or missing a second rack.
Rack were ordered and delivered in one day. great service. Read more
The 8 Inch Trim Ring is an OEM part for GE ranges and cooktops. It fits around the 8-inch burner elements, providing a clean, finished look while also helping to contain spills and crumbs on the stovetop.
Symptoms of a bad 8 Inch Trim Ring include:
Causes of a bad trim ring can include frequent exposure to high temperatures, spills of acidic or sugary substances that cause corrosion or damage, and general wear and tear from cleaning and use.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
If you’re looking to replace all of the trim rings and drip pans:
Replaced above parts, easy to do, looks like a new stove. Needed to pry open knob stem slot segments very slightly to remove broken plastic from previous knobs. Spreading stem slot metal sides too much and they will break. With slots cleaned out, pinch stem sides almost together for new knobs to slide on. Customer service rep was helpful and parts delivery was next day as promised. Before contacting Appliance Parts Pros, I found their on-line customer reviews were much better than their... Read more
Replacement oven rack for ranges. Holds cookware inside the oven cavity. Replace if cracked, warped, bent, rusted, or missing from a used appliance.
I measured my oven racks which are 24"X18" and ordered two new ones and had them within three days of my order! They are perfect! Read more
The 6 Inch Small Drip Pan is an OEM part for GE ranges and stovetops. It is designed to sit beneath the burner element to catch spills and drips that occur during cooking. This helps keep the stovetop clean and reduces the risk of burns and fire by preventing spills from coming into direct contact with the heating elements. For the 8-inch large drip bowl order WB32X106
Symptoms of a bad Drip Pan include:
Common causes for replacing the drip pan include prolonged exposure to high heat which can cause discoloration and deformation, as well as accidental damage during cleaning or heavy use.
We ordered the parts from Appliance Parts Pros., and they fit perfect!!! (have replaced in the past with cheaper ones from local store/didn't fit right and didn't last) this would be the 4th or 5th time we've used Appliance Parts Pros and I keep coming back because they're AWESOME!! Online search is good; and if you have questions the instant chat/customer service is even better! Thank you Read more
Burners won't light or igniters click constantly? This igniter switch and wiring harness assembly restores spark ignition on gas range surface burners.
Replacing the bad harness switches with the new set fixed the problem. Read more
Burner not heating or 'Hot Surface' light stays on? This electric cooktop surface element is likely the fix. DIY-friendly, most installs take 15 minutes.
Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.