Samsung Parts

• Won't start

I am so blessed. I went online. Found the brackets. Watch the video for the brackets I chose. And lucky me. I did not have to pull the dishwasher out. The installer did not have it flush under the counter. So I was able to pull the dishwasher forward unhook the damage brackets and insert the new. Put the dishwasher back in. Two screws. Now the balanced and secure dishwasher washes better than ever and I did not have to pay an extraordinary fee for a repairman. I'm 68 and take care of a 72 year... Read more

• Frost buildup

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

Replaced knob. Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

Watched your repair video. Ordered the part. Fixed it! Read more

After watching the how to video twice I decided to embark on dismantling my dryer and attempting to replace my motor. After realizing that the main tool needed was a Phillips screwdriver I was sure I could handle this repair. One by one I took apart the dryer and spread out the parts throughout my mud room. 1.5 hrs later and I have a working dryer, and most of all a happy wife. Thanks for the speedy part delivery and the great how to video. Read more

We sent an email to AppliancePartsPros.com asking for their help in fixing our range. We gave them the model number (NE58F9500SS) of our Samsung Electric Range and told them about the faulty/dangerous two dual burners. We hated to get close to the range because the burners would turn on if you barely brushed by the range or if you would reach across it and accidentally touch the burner knobs all of a sudden you would feel heat or just see the light indicating the burner was on. We were... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Replaced the ice tray. Read more

Samsung refrrigerator. it started when the setting was on cubes but was putting out crushed ice. then months later the water refill was running down into the ice bucket causing a massive block of ice in the bucket. look closely at the first two or three cubes in the ice tray after they unload. mine were not dumping and staying in the tray. when the water refill kicked on it would overfill the tray (because of the leftover cubes remaining in the tray) and would run down into the ice bucket... Read more

Luckily happen to be walking by when machine started to make "grinding" noise as washer tub started to hit plastic tub. Assuming by shutting down machine, prevented any more damage. Aside from noise, when we opened door, tub appeared "crooked" tilted back a lot further then normal. When we removed the rubber door seal, could spin drum and hear and see the wobble and grinding. Internet told us the possibilities and so we proceeded to break down the machine. A drill with Philips bit and... Read more

• Ice maker dispenses too much ice
• Ice maker not making ice

Purchased both the ice maker assembly and the valve assembly to replace the parts as needed. replaced the ice maker assembly first, and this fixed my problem. Took about 10 minutes, mainly because I didn't watch the YouTube video first. Had I watched that, it would have probably taken even less time. One Philips head screw driver is all you need. Read more

Replaced the evaporator cover asy.. Read more

The replaced part was perfect....only took 35 mi to do the job. Thank you. Read more