Samsung Parts

I ordered the part (drain pump assy) from AppliancePartsPros.com and it was delivered to my house in 2 days. I called a friend to install it for me but....he never showed up. So I decided to do it myself. I watch the video that another Appliance Part customer suggested and it was extremely easy even for a seasoned woman as myself. It only took me about 20 minutes. Test load was perfect with no errors. This morning I'm on load 5 and still no issues. Thanks Appliance Parts hopefully I won't ever... Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

After looking online and discovering that others who had used a knockoff brand filter to "save money" had the same problem, I concluded the only solution was to replace the filter housing. Found the one I needed on AppliancePartsPros.com. Most important to me was the video explaining how to replace the filter housing - it made the task a snap to complete. The price was also competitive with other sources. Shipping was half that charged by Samsung. Not only was it cheaper, but it was also super... Read more

• Door latch failure

I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more

• Won't start
• No heat

Unplugged range, removed back panel. Loosened plug block from range, unhooked wires from existing element, then sliced through insulation between element ends with sharp knife. Removed screws holding element ends then removed element. Inserted new element, screwed it in place, connected wires and replaced plug block. Vacuumed up fiberglass insulation dust and replaced back panel. Replaced plug then tested. Read more

• Too hot
• Takes too long to dry
• Doesn't shut off

Did google search and found youtube diagnostic and repair video. Blower wheel was warped and rubbing on the cover. We ordered a new blower wheel and followed youtube instructions to install new blower wheel. Read more

The error code implies a faulty fill valve. This was not the case for me. Replacing the main PCB assembly solved the problem. I have run two full loads since the repair with no problems. Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Found one of the drain valves was clogged causing condensation to overflow on the floor behind the refrigerator. Order the parts on Monday morning and they arrived tuesday afternoon. Replace both of the valves in 15 minutes. Easy repair and save a bundle over a service call. Read more

Unplug fridge. Use a Phillips head screwdriver to remove the single screw underneath the display. Also under the ledge you will see two slots - one on each side of the forward part of the ledge. Insert a flat-head screw driver and twist (either way) to release the plastic tabs. Once the tabs release you can pull the whole thing loose. Unplug the wiring connector and set the display face aside. Next TAKE A PICTURE OF WHAT YOU SEE WITH YOUR PHONE so you know how everything fits... Read more

• Fridge too warm
• Doesn't shut off
• Noisy

The blower motor that circulates air through the refrigerator was broken. I had to remove all the shelving and drawers from the refrigerator. Then I had to remove the plastic light cover from the center of the fridge. Then I removed all visible screws to uncover the evaporator/radiator. I then unplugged the light bulb and motor wires. Luckily all wiring is keyed so that it can be plugged in again without error. I removed the motor by opening the motor housing. The housing has 1 screw and... Read more

We had a hard time finding a tutorial that showed how to replace the part of the handle that broke. After several attempts to fix on our own we gave up. A few weeks later a friend came to our house and we were discussing the fix for the handle and She helped me to fix the handle just buy trying a new way to remove the old broken part. It took us several tries but with her help I was able to fix the door handle and remove the broken part. I really wish your site had a tutorial for this... Read more

We had a hard time finding a tutorial that showed how to replace the part of the handle that broke. After several attempts to fix on our own we gave up. A few weeks later a friend came to our house and we were discussing the fix for the handle and She helped me to fix the handle just buy trying a new way to remove the old broken part. It took us several tries but with her help I was able to fix the door handle and remove the broken part. I really wish your site had a tutorial for this... Read more

• Little to no heat when broiling

I had the choice of spending $2K on another double oven stove or $60 on two elements. (I felt more secure about replacing both bake and broil elements just in case the fire had damaged the bake element) It was an easy decision and quick replacement! Power was already off to the stove so I cleaned up the fire retardent mess. I even found easy instructions dismantling the oven door in order to clean the powder residue from between the glass. I then removed the rack and remaining old elements. I... Read more

Watched the first half of your online video and followed your steps. Easy video to follow. I had a newer model so there were a few adjustments, but it was very easy to follow. Read more

• Light not working

Perfect, everything works now Read more