Need Help?
Call or text
Structural part that supports the washer drum and connects it to the drive system. Replace if cracked, corroded, or broken to restore proper drum support.
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more
Replace your washer door boot seal when torn or leaking to prevent water damage. Fits Samsung front-load washers. Verify fit with your model number.
I looked up my model number on the site, and found my parts needed. J then watched a video from repair clinic on you tube. The video was sr sight forward, and made the repair easy. I have repaired washers and dryers for numerous people following the same process. Doing this has saved hundreds of dollars in labor charges. Read more
Replaces cracked or broken spider and shaft assembly that supports the inner drum. Installs inside washer tub. Needed when assembly has failed.
Luckily happen to be walking by when machine started to make "grinding" noise as washer tub started to hit plastic tub. Assuming by shutting down machine, prevented any more damage. Aside from noise, when we opened door, tub appeared "crooked" tilted back a lot further then normal. When we removed the rubber door seal, could spin drum and hear and see the wobble and grinding. Internet told us the possibilities and so we proceeded to break down the machine. A drill with Philips bit and... Read more
Fix a washer door that won't close or lock with this door latch assembly. Typical repair for broken latches takes about 15 minutes. Easy DIY install.
I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more
Fix washer that won't fill, overflows, or fills slowly. This water inlet valve controls water flow into your washer. DIY-friendly repair with video guide.
Watched your repair video. Ordered the part. Fixed it! Read more
Creates watertight seal between washer drum and door. Replace if torn, cracked, or leaking during wash cycles. Verify fit with your model number.
Fairly simple fix. followed you tube video step by step..needed a set of extra hands (wife came in handy) when installing gasket..after several loads as a test, no leaks. Read more
Replace your broken or missing dryer control knob encoder assembly. This dial installs on the control panel to adjust cycle settings and temperatures.
Ordered a new knob and took out little bits of the old one. Took the new knob and pressed it over the stump and presto works like new. Read more
Fix NF, OE, or 4E error codes on your washer. This water inlet valve controls water flow into the drum. DIY repair takes about 15 minutes.
The error code implies a faulty fill valve. This was not the case for me. Replacing the main PCB assembly solved the problem. I have run two full loads since the repair with no problems. Read more
Suspension damper rod assembly installs at the corners of the tub. Replace if cracked, broken, or worn to restore proper tub support and stability.
Washer started every cycle just fine. With just 9 minutes left on the cycle, when it started the spinning cycle it would stop and on the display showed a DC error code and it would kick the cycle to the beginning of the wash. After asking around and doing a little you tube research I called appliancepartspros.com and ordered http://www.appliancepartspros.com/samsung-assy-damper-owm-dc97-16350d-ap5579032.html ordered all 4. Replaced them and after that it the washer it being working just fine.... Read more
Replace your washer door boot seal if you notice water leaking from the door area. This rubber gasket creates a watertight seal around the door opening.
Ordered a new outer door seal and watched their video before replacing. Easy to follow the video and it took me less than 30 min to complete repair. A small amount of diluted dishwashing liquid on the new seal lip makes the install much easier. Read more
Prevents water leaks by sealing your washer door during wash cycles. Replace if torn, cracked, or crusted with detergent buildup. Verify fit with your model.
Appliance Pros made sure I had the correct part by verifying the model of my appliance. The part arrived on the scheduled day as promised I did the repair it myself. Read more
Suspension damper rod assembly for washers. Mounts between drum and frame to absorb vibration. Replace if worn, damaged, or causing excessive movement.
Samsung top load washer, about 3 years old started throwing a DC error code more and more often. Initially started with large loads. Wash would get to spin cycle, start wobbling all over the place, stop and refill then try again. Eventually it would stop and throw the DC code. As time went on, the size of the loads got smaller and smaller. Research here indicated that suspension rods probably need replacing. I bought 4 rods for replacement for about $90 in total inc. tax & shipping.... Read more
Seals the washer door to prevent leaks. Replace if torn, moldy, or causing water leakage. Verify fit with your model number before ordering.
Watched the first half of your online video and followed your steps. Easy video to follow. I had a newer model so there were a few adjustments, but it was very easy to follow. Read more
Fix a washer that won't fill with water or leaks onto the floor. This water inlet valve controls water flow into your machine. DIY repair in 10 minutes.
The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more
Washer overfilling or not filling properly? The water level pressure switch controls fill cycles. Easy 15-minute DIY repair with our video guide.
This error code indicated faulty water level and wash cycles were exhibiting either no water or too much water. Saw utube vid using this part for this type of problem and so far the repair is working well. Part arrived in 2 days, it was the right part and the machine is working the way its supposed to so I'm very happy. The worst scenario would have been to hire a repair guy to rip me off for a "Johnson Rod" I didn't need. Read more
Washer won't start or shows LO/DC error? Lid lock assembly secures the lid during cycles and signals the control board. DIY-friendly repair with video.
After watching the video it was strait forward. Just Pull the screws pop the lid swap the springs "grease them" and put it back together. I would suggest that you have a person help you mostly has a second pair of hands. The lid was over rear springs and it will save you some expletives to have the extra body. I had worn out springs and the load kept becoming unbalanced during spin cycles I just happened to coincide with the Lock mechanism failing. The motor drive for the lock stopped working.... Read more