Dishwasher Run Vent Push Button Switch Parts

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more

Removed the lower rack, removed the lower wash arm, removed the lower coarse filter, removed fine filter ( still no tools require to this point). Removed two 1/4" head screws with nut driver to then remove float switch, unplugged float switch, plugged in new switch, reinstalled filter, etc. This is a 5 minut job! Read more

Tried to fix with a non GE part, didn’t work. Your GE brand pressure sensor worked like a charm Read more

• Won't start

The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

I got on the site and shared my issue. It was determined my door switches were bad, as well as my actuator. I ordered the parts (which arrived in just 2 days!) and I fixed it myself in just under 10 minutes, for under $30.00. Thanks guys!!!! Read more

I had an appliance repair guy come and he told me it was possibly the vent assembly but if changing it didn't fix the problem it would be the control board next. He felt it was not worth the money to repair because he would have to disconnect everything just to get to the vent on the right rear top of the dishwasher. When i took the DW out thinking i had to buy a new one i saw this part was stuck open and covered in limescale deposits and grime.I ordered the part from appliance pros and payed... Read more

This was a difficult problem to diagnose. Because the machine would start the wash cycle then shut down after a few minutes of running, it appeared that the cause might be a bad thermostat or heating element, but all checked out ok. That led me to believe that the control panel may be the culprit but it also appeared to be working correctly when I ran the diagnostics program. A visual examination of the components found that the door switch electrical connections looked discolored, so I removed... Read more

• Will not fill with water

Replacing the inlet valve solved the problem. The old valve was somehow clogged with white sediment. I probably could have taken it off and cleaned it out if I'd known, but replacing the valve was much easier. Took about half an hour to repair. Video walk through was extremely helpful. Great to have a working dishwasher again! Read more

• overflowing
• Will not fill with water

I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle. Read more

Fix went fine, had to pull the dishwasher out to replace flood switch control board was very easy to replace, and fixed the problem. Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more

I had to pull and clean the pressure sensor switch four times in a year. Each time more gunk accumulated. When that happens the sensor does not close the water valve. The dishawsher keeps filling and the water comes out through the overfill port. The water then goes in the catch basin under the washer and floats the emergency switch. This cuts off the water but keeps the pump running just in case. Tripping the circuit breaker is only a temp fix. What happens is the water level may have... Read more

This was a very simple repair. It was done in about an hour. It involves disconnecting the dishwasher, emptying the water from the inside, taking it out and flipping it over, and replacing the diverter motor. This repair is done on the underside of the dishwasher, nothing to disconnect inside (just remember to remove the baskets). It would be wise to order the motor seal and micro switch that goes with it as they are all cheap parts and easy to swap out during the procedure. Be sure to take... Read more

The parts from AppliancePartsPros.com arrived a day ahead of schedule. (I'm a big APP.com fan.) I removed the metal front door panel, then removed the broken plastic Panel-Facia which houses the handle. Because the buttons and handle trim needed to be transferred from the old Panel-Facia to the new one, I expected that, also being plastic, they may break when making the transfer, so I ordered all of those parts as well, which only drove the cost up about $32. If I broke one item in the... Read more

• Not drying dishes properly

The solenoid that opened the air vent for drying was broken so it was open during the wash cycle allowing water to escape into the air duct. Found the part at SearsParts and AppliancePartsPro, and Sears was $15 more expensive. I ordered on Friday from AppliancePartsPro and selected standard shipping and the part arrive the next day (Saturday). Amazing service. AppliancePartsPro will be my first stop in the future. Read more