Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Factory fastener screw secures panels, brackets, and trim inside appliances. Replace missing, stripped, or damaged screws to restore tight fit.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more
This genuine replacement part is a drive motor for dryers. The drive motor is the main engine that allows the dryer drum to rotate. If the drum is no longer spinning properly, the drive motor might need to be replaced. Luckily this is a relatively simple process.To replace the drive motor, begin by unplugging the dryer. Once it is powered off, uninstall the front panel of the dryer by removing the screws that attach it. After that, lift the top panel above the drum so that it is vertical and no longer covering the drum. Then disconnect the wires from the moisture sensors with a screwdriver by pressing down on the locking tab. Once the wires have been removed, lift the drum out from the dryer to gain access to the drive motor. Using a socket wrench, remove the blower wheel from the motor assembly. Then remove the old drive motor by unthreading the mounting screws that attach it. Install the new drive motor and reassemble the dryer. This OEM replacement part is sold individually and is compatible with Whirlpools, Maytag, Kitchenaid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dryers.
Replaced all damaged parts, rear drum rollers, front drum 'bearings', felt seal infront of drum, idler pulley and arm. Lastly replaced motor. Hopefully will work for another 11 years?? Videos were awesome, telephone assistance was great as welll. Thank you. Read more
Dryer not heating or producing warm air? This heating element assembly often solves no-heat issues. DIY-friendly repair, typically 10-20 minutes.
I figured there could only be a couple reasons why the dryer would not heat so I did some research. I read where you could test for continuity on the parts to determine which one was bad. A friend referred me to this site, I looked up the part for my particular model, ordered and replaced the part. It could not have been any easier. I will come back to this site with my future appliance parts needs for sure! Read more
The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.
Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.
Symptoms indicating the need for a gas conversion kit include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
The kit was very simple it took longer to take the dryer apart than it did to do the change over and it works great thank you for you're product Read more
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Replaced flow meter and control valve Read more
This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.
Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more
Dryer not heating or flame goes out after a minute? This gas valve with coils restores heat. 15-minute repair with video guidance available.
Replaced valve had some trouble removing the fitting from the valve as the new fitting was slightly too large and had to be replaced with the fitting from the old valve. Used a large crescent wrench to grip the valve at the base and I was able to apply enough force to remove both fittings transferring old fitting to new valve. The instructions were detailed and excellent. The dryer is up and running fine. Read more
Seals the dryer door to keep heat and moisture inside the drum. Replace when worn to restore airflow, improve drying, and stop lint escape.
I replaced the gasket that you had sent to me the next day in about 5 minutes! Sears parts direct had the item back ordered and even when I cancelled the order, they still shipped it! I will never use them again! All my appliance part needs will be through Appliance Parts Pros! Read more
Dryer won't heat or flame cycles on and off? A warped burner assembly prevents reliable ignition. Moderate DIY repair restores even drying.
When I first looked at my dryer I thought it was my ignitor, on a closer look I found that about an inch of my burner assembly arm was laying in a corroded mess on the bottom pan of my dryer. I came online and found your website. After reviewing your parts I thought well I can probably get those local and with competive pricing. Wrong!! There are 3 appliance parts stores withing about 3 miles and I checked them all. Higher prices by 25-35% and longer wait times than your advertised... Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Dryer making loud noise or won't dry? A cracked or loose blower wheel often causes poor airflow. Moderate DIY repair, 1-2 hours with basic tools.
I disassembled my dryer and found that the fan(blower wheel) was "free-spinning" on the motor shaft. A common problem with this model Maytag dryer. I also discovered that the right drum roller (drum support roller) was in the process of failing. Note: the fan drive was frozen on the motor shaft, this was the threaded type of motor and fan assembly. I was able to remove the fan drive by using vice-grip pliers, hammer and a combination wrench to hold motor from turning. Also Note: the fan... Read more
This jumper wire connects two terminals in an appliance circuit to maintain proper electrical continuity. Replacing a burnt or damaged jumper restores reliable connections so switches, heating elements, and controls receive power as designed.
Replaced jump wire and thermostat. Read more
The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.
Symptoms of a bad Leveling Leg Pad include:
Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
For the leveling leg order 22003428.
New leveler pads Read more
Washer won't spin or door won't lock? This door lock spin enable switch signals the control to start high-speed spin. Moderate DIY repair, 30-60 minutes.
Replaced the motor wax door lock switch and the door lock spin enable switch. Read more
Channels water from the door boot back into the drain path. Replace if cracked or clogged to prevent front leaks, standing water, and musty odors.
Basically rebuilt the washer from the ground up. Spent more money than a new washer but we have been so happy with the way this machine has worked over the last 19 years figured it would be money well spent. Read more
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
Took off cover, installed new parts. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.