Psd 262 Lhew Parts

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

• Won't start
• Door latch failure
• Door won't close

With the power to the dishwasher on, I removed the six or seven screws holding the door panel together. With the door separated, I manually moved the switch which should close when the dishwasher latch closes. This illuminated and activated the control panel telling me that the problem was in the door latch. I purchased a new latch from appliance parts pros and installed it. Very easy fix for a homeowner, taking thirty minutes. Read more

If you have a problem of water pressure when you press for water at the dispenser your problem migth be your filter head assembly. Thanks to appliAncepartspros for their assistance Read more

We ordered the item appliance parts pros said would fit our make/model. the part arrived in perfect condition faster than i could possibly imagine, and while it fit our machine, it was a big bigger than the original and it fits off-center, but i guess it works fine! excellent speed and ease of ordering. thanks Read more

• Will not dispense detergent

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

I replaced the auger motor. You have to remove complete ice maker. Everything is just like help video to do except yoke dispenser. I watched video several times. Yoke will not just tap loose, after 30 minutes of tapping, I was using screwdriver to brace. I used a Dremel tool to cut part of shaft, came off easy then. After that, the repair went great. I have ice, I noticed motor I received was stronger. Parts came on time stated and worked great. I will order again on other repairs. Read more

I found my parts and ordered the six I needed, however I did not pick up on the difference from the front wheels to the rear wheels in the the descriptions. The rear wheels are narrower and I ordered all front wheels, six fronts instead of four front and two rear. I made it work by using the axle from the new wheel with two old narrow wheels. Read more

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

• Door won't open or close
• Door sweating
• Fridge too warm
• Clicking sound

Used floor jack to lift and secure door, left upper hinge point in place, removed lower hinge support, removed old cams and installed new ones and lubricated, secured and adjusted hinge . Read more

Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more

Viewed the replacement video on the appliancepartspros.com repair process to see how complicated the repair was. Replacement part ordered but took a full 7 days to cross 2 states?? Replacement part was authentic replacement and was installed in about 15 minutes. One thing that was not mentioned in the video...make sure the water spout in routed correctly into the ice maker. While we were ordering, replacement crisper drawer ordered as well. Read more

Replaced the upper and lower racks. AppliancePartsPro shipped the racks fast and they are a perfect fit. I think they're even a better, stronger design then the factory originals. Read more

Replaced with a new Inlet Sump [WD18X213]. It was a little tedious, attaching the Inlet Sump, back to the pump, because I did the job with the dishwasher in place (not pulled out). My dishwasher was plumbed with copper pipe, so I really didn't want to upset that. Also, I had previously replaced the motor and the pump in this dishwasher, so I was familiar with how the Inlet Sump attached to the pump. Again, it's very tight working under the unit while it is still in place, and I wouldn't... Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

The replacement arm arrived promptly. Removing the old spray arm hub was very difficult by hand, plumbers wrench, or adjustable wrench. However, by inserting a screwdriver trough the two opposite holes where the tabs had broken off, it is relatively easy to unscrew the old hub. Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more