Maytag Refrigerator Parts

• Ice maker dispenses too little ice
• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself. I investigated the ice maker by removing the freezer food sliding tray and hanging tray, and then unscrewing the door off the slides. When I looked inside at the ice maker, I saw the tube where... Read more

• Touchpad does not respond
• Ice maker not making ice

Located the Whirlpool crisper pan on AppliancePartsPros.com on Monday morning and received the crisper pan on Tuesday afternoon. Doesn't get any better than than!! I will be repeat business in the future!! Read more

• Ice maker not making ice

After researching a number of sites for a diagnosis I tended to think the culprit was going to be the ice maker thermostat. Checking pricing and availability of the thermostat prices were very close at $40 BUT wait now you have to but the thermo mastic at another $35-$40. And after some continued research the factory ice maker in a $3000 msrp 4 door refrigerator was/is known to be defective long after warranty period expires. So it only made intelligent sense to buy the entire icemaker at a... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

All you need is a nut driver. The end cap is attached to the side of the refrigerator cabinet with two long screws. Once you remove them, you should slide the end cap towards you. It will release the internal clip that holds the front of the end cap. You should then unscrew the metal slider from the end cap. Assembly of the new end cap is the reverse. You should first attach the metal slider to the new end cap. Attaching the new end cap to side of the refrigerator cabinet is a little tricky.... Read more

While looking for parts thru AppliancePartsPros.com, I found a diagram with my refrig model # for the door shelf bin. It was a perfect match. Prior to that I've spent countless hours searching and became very frustrated. The diagrams and videos were very helpful. Thank you, KShigeta Read more

I replaced the icemaker. It was fairly easy, with the most difficult part being access to the icemaker in the bottom freezer. I loosened two screws, removed one additional screw, disconnected the wiring and removed the old icemaker. I mounted the wiring harness and ice level sensor arm from the old unit onto the new icemaker and installed it with no problems. I wish I'd done this months ago instead of repeatedly attempting to repair the old icemaker. Read more

Replaced ice maker unit. 4 screws to remove cover on inside door. 2 screws for ice maker. Three connectors: ice maker on/off switch, LED light, wiring harness connector. A second person assisted by bracing the door for me, but not necessary to get the job done. I also used some cellophane and tape to cover the door opening for the 5 minutes it took to replace the unit. Again, not necessary, but it was quite warm out and it kept the freezer contents from thawing out. Appliancepartspros.com had... Read more

• Won't start
• Ice maker won't dispense ice

No water was making it to the icemaker, so I first replaced the dual water valve. The valve was bad, but still no water at the icemaker. So I ordered the recommended icemaker from AppliancePartsPros. It arrived in a couple of days and took less than 15 minutes to drop in. The new unit was producing ice in less than 30 minutes. Your parts search, photos, repair videos and quick delivery made the whole process painless. Read more

• Not dispensing water

I ordered the water filter and when it came in I replaced the one in the fridge, held the button down for 3 seconds and the light went off. Read more

• Not dispensing water

Our Kenmore (Whirlpool) refrigerator's ice maker had stopped making ice. I searched YouTube and found a repair videos for this exact problem, finding one with a similar refrigerator and the identical ice maker. I learned that the Water Inlet Valve had likely gone bad and would need to be replaced. In the video the tech pointed out the small rubber tube inside the freezer that comes down from the ceiling of the refrigerator into the ice maker. This tube feeds it the water to make ice with and... Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more

Installed replacement drawer Read more

No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more

It was a classic horror story, but with a happy ending! I called a classic, "regular" repair company that I obtained on-line. My Whirlpool was 2 months out of warranty, so the repairman charged a trip-fee of $95 that would be subtracted from the cost of my repair. "Lee" showed up an hour late, even though he was told that I had to leave for work by 10:30 (-He assured me that he would have me fixed by then). The refrigerator was rolled out of its spot, and Lee began to remove the back cover... Read more