Thermador Parts

The Oven Door Gasket Kit is an OEM replacement part for 27" Bosch wall ovens. It includes a gasket for insulating the oven cavity while in use and clips to secure it. Over time, heat and compression can break down gasket material allowing potential leaks of hot air from the oven during cooking or difficulty closing the door. Causes involve standard wear from repetitive door closing as well as exposure to high oven temperatures over many heating cycles.

Symptoms of failed gaskets include: 

• excessive heat escape from the door opening
• Door locking difficulties
• visible cracks or tears in the gasket materials 

Replacing the gasket allows for smooth door movement and an tight seal when closed. This Bosch part can also be used on Thermador and Gaggenau appliances.

This jet holder mounts in the burner assembly for a 12,000 BTU burner. It positions and secures the orifice (jet) and helps seal and align the gas path so the burner lights reliably and produces a steady flame.

• Holds and aligns the burner orifice for the 12,000 BTU burner
• Provides a sealed passage from the valve to the burner head
• Helps restore proper flame height and pattern when the original holder is stripped, cracked, or corroded
• Common symptoms: weak or uneven flame, burner won't light, or jet/orifice will not seat securely

• Shut off gas supply and power; allow the appliance to cool before starting
• Remove grates, burner caps, and burner head to access the holder
• Transfer the existing orifice/jet to the new holder; tighten fittings carefully—do not overtighten into soft metal
• Reassemble, restore gas, and perform a leak check with an approved solution

This bake element heats the small oven cavity from below during Bake, delivering the radiant heat needed for preheating and consistent baking when the original element fails.

• Provides primary bake heat at the bottom of the small oven cavity
• Works with the oven control to preheat and maintain set temperature
• Common failure symptoms: no or weak bake heat, uneven baking, visible blistering/cracks, or a breaker trip when Bake is selected

• Disconnect power at the breaker before servicing
• Access is typically from inside the cavity; remove mounting screws, pull the element forward, and move wires one at a time
• Support wires so they don't retract into the insulation; avoid bending or stressing the new element
• Restore power and run a bake cycle to verify proper heating

The Cooking Tray is an OEM part for Bosch microwaves. As the centerpiece of the microwave, the cooking tray ensures even cooking by rotating food items during the cooking cycle. It supports dishes and rotates continuously to evenly distribute microwave energy throughout recipes.

Causes of a bad cooking tray can include wear and tear due to extended use over time. Food splatter or spills left inside the microwave may damage or corrode the tray. Accidental dropping or cracking of heavier dishes placed on the tray can also cause issues.

Symptoms of a bad cooking tray include:

• The tray not spinning or rotating properly during cooking
• Unevenly or partially cooked food
• Loud grinding or scraping noises coming from the tray
• Cracks or breaks visible in the plastic surface

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

This front leveling leg supports and adjusts the appliance at the front, helping it sit stable and truly level. Replace a damaged or missing leg to restore proper height, stability, and smooth door alignment during everyday use.

• Provides height adjustment at the front to level the appliance
• Helps prevent rocking, vibration, and rattling
• Maintains correct cabinet/door alignment for proper operation
• Replace if the foot is cracked, stripped, missing, or won't adjust
• Common signs: unit wobbles, sits unevenly, or is difficult to level

• Disconnect power; if applicable, shut off water or gas. Pull the appliance forward and remove the toe-kick/access panel for clearance.
• Protect the floor; tilt or raise the front slightly to reach the leg.
• Unscrew the damaged leg; thread the new leg in by hand to avoid cross-threading.
• Adjust height until level front-to-back and side-to-side; verify stability before returning to service.

This Thermal Fuse is an OEM part for Bosch Wall Ovens. It acts as a safety mechanism, designed to interrupt the electrical connection if the oven's temperature exceeds the safe limit.

What Causes a Bad Thermal Fuse:
Overheating due to issues like a malfunctioning thermostat or restricted airflow can cause the thermal fuse to blow. This interruption prevents the oven from operating at dangerously high temperatures, reducing the risk of fire.

Symptoms of a Bad Thermal Fuse:

• Oven fails to heat up
• No response or display on the control panel
• The oven doesn't maintain the set temperature

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door seal creates a watertight barrier between the dishwasher door and tub to contain wash water and steam. Replace a worn gasket to stop drips from the door area and restore a reliable, quiet seal.

• Seals the perimeter of the door to help prevent leaks at the sides and top
• Helps the door close snugly and contain moisture/steam
• Replaces seals that are cracked, flattened, deformed, or shedding pieces
• Typical symptoms: water on the floor near the door, dampness around the door frame, visible wear, door harder to close

• Disconnect power and turn off water supply before servicing
• Pull the old seal straight out; clean the groove/channel of residue and debris
• Warm the new seal to relax it; start at the top center and press it fully into the groove, ensuring corners are evenly seated
• Close the door for several hours to help the seal set, then run a short test cycle and check for leaks

This grease filter is a genuine Bosch part, sold individually. This grease filter can be used as a replacement part for a range vent hood. This part prevents the accumulation and buildup of external grease in the internal aspects of the range vent hood. A grease filter can be subject to damage within the lifespan of a range vent hood. This damage can manifest in the form of punctures, scrapes, nicks, tears, and erosion to the material that can allow external grease to slip into the range vent hood and gunk up its inner workings. A grease filter might become damaged from general wear and tear or due to a collision with a hard object that warps the component beyond functionality. If this occurs, the grease filter should be removed and replaced with this genuine OEM replacement part. It is a simple replacement process that will require no special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This grease filter is compatible with the following appliance brands: Bosch and Thermador.

The Water Filter Cap is an OEM part for Bosch refrigerators. This secures the water filter within the refrigerator, ensuring a snug and leak-free fit. 

The need for a replacement can arise if the original cap is lost during a filter change, damaged, or wears out over time. 

Symptoms of a missing or damaged Water Filter Cap include:

• Difficulty in installing or securing the water filter properly, which could lead to water leaks inside the refrigerator.
• Contaminants or particles in the dispensed water, indicating that the filter is not fully sealed and thus not effectively filtering the water.
• The water filter becoming loose or falling out, compromising the refrigerator's ability to provide clean, filtered water.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

This drain hose adapter connects the appliance's drain hose to another hose or a compatible fitting, providing a secure, leak-resistant joint so wastewater can be routed to the household drain. Replace when the original adapter is cracked or loose.

• Couples the drain hose to another hose or to a sink/disposal/standpipe fitting
• Helps seal the joint to reduce leaks and hose slippage
• Restores a tight fit when the original adapter is worn, brittle, or missing
• Symptoms of a bad adapter: leaking at the connection, hose won't stay attached, visible cracks

• Disconnect power and turn off water before servicing
• Place a towel or pan to catch residual water from the hose
• Fully seat hose ends over the adapter barbs and secure with appropriate hose clamps
• Run a short test cycle and inspect all connections for leaks

The Cooktop Bracket Kit is an OEM part for Bosch cooktops. This bracket and hardware kit serves to securely fasten the cooktop surface to the underlying countertop.

Causes of a bad bracket can include wear and deformation from heavy cooktop use over time, or damage to fastening screws from accidental impacts.

Symptoms of a bad bracket and fastening kit include:

• The cooktop surface becoming loose, wobbly, or unstable during use
• Gaps appearing between the cooktop and countertop edges
• Reduced heat containment and risk of burns from loose surfaces

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Mount, Vibration Rubber Range Hood is an OEM part for Bosch range hoods. It plays a crucial role in mounting the range hood itself and reducing noise and vibrations produced during operation. The rubber vibration mount is designed to absorb shocks and isolate noises, providing a smooth, quiet ventilation experience.  

Symptoms of a bad mount can include looseness or detachment of the range hood, increased vibration transfer to surrounding cabinetry, or failure of the rubber material itself.

Symptoms of a bad mount include:

• Noisy operation from the range hood that transfers to cabinets
• Visible vibration of the range hood body during ventilation  
• Eventual detachment or loosening of the range hood mount
• Reduced vibration damping translating to a rougher ventilation cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore range hood models.
 

This micro switch is a small, fast-acting on/off switch tripped by a mechanical lever or float to send a signal to the control. Replacing a worn microswitch restores accurate sensing so the appliance starts, stops, and runs when it should. What it does

• Senses the position of a linked mechanism (lever, float, latch) and opens/closes an electrical circuit
• Helps the control enable or disable functions only when conditions are correct
• Failure symptoms include intermittent operation, cycles that won't start, or a unit that keeps running until power is removed

• Disconnect power and, if applicable, shut off water before servicing
• Access the switch and note actuator orientation and terminal layout
• Move wires to the new switch one at a time to maintain correct placement; ensure tight connections
• Manually actuate the mechanism to ensure a positive "click" and proper operation before reassembly