Thermador Parts

This electronic PC board is the appliance's main control, processing inputs and directing power to components so cycles run correctly. Replacing a failed board can restore normal operation when the unit is dead, won't start, or stops mid-cycle.

• Interprets user inputs and sensor feedback to execute programmed cycles
• Switches relays to power motors, valves, heaters, and other loads as required
• Manages timing, temperature, and safety logic for consistent performance
• Typical failure symptoms: no power/won't start, unresponsive or erratic controls, cycles ending prematurely, recurring error codes

• Disconnect power before servicing; verify power is off with a meter
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time to identical positions on the new board to prevent miswiring
• Some models require service-mode setup or calibration after installation—follow your model's service documentation

The Cooking Tray is an OEM part for Bosch microwaves. As the centerpiece of the microwave, the cooking tray ensures even cooking by rotating food items during the cooking cycle. It supports dishes and rotates continuously to evenly distribute microwave energy throughout recipes.

Causes of a bad cooking tray can include wear and tear due to extended use over time. Food splatter or spills left inside the microwave may damage or corrode the tray. Accidental dropping or cracking of heavier dishes placed on the tray can also cause issues.

Symptoms of a bad cooking tray include:

• The tray not spinning or rotating properly during cooking
• Unevenly or partially cooked food
• Loud grinding or scraping noises coming from the tray
• Cracks or breaks visible in the plastic surface

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Fixes no spark at burners or oven not lighting issues. This ignition module generates the high-voltage spark needed to ignite gas at electrodes.

Fixes ice maker overflow and water leaking into freezer. This water inlet valve controls water flow to your dispenser and ice maker. DIY repair.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Air-gas mixing tube that connects the orifice to the burner head on gas cooktops. Replace if clogged, damaged, or missing to restore proper flame mixing.

Traps grease and odors during cooking. Replace when clogged or discolored for effective ventilation. Verify compatibility with your range hood model.

Replacement drip pan that collects defrost water and condensation beneath your refrigerator. Needed when original pan is cracked, broken, or missing.

Refrigerator not cooling or freezing up? A failing evaporator coil causes cooling loss and frost buildup. Requires EPA-certified tech for installation.

Screw: 8-16 x 3/8 inch.

Oven won't start or stop correctly? A faulty micro switch prevents proper sensing of linked mechanisms. This switch restores accurate control signals.

This is an 8-inch coil-style surface heating element that plugs into a burner receptacle on the cooktop of your range. It provides radiant heat for cooking on the stovetop. Replace this element if the burner doesn't heat up, heats unevenly, produces visible damage such as pitting or blistering, or fails to glow red when turned on.

This 13.7 mm venturi tube mixes gas with air for proper cooktop burner operation. Replace if original is clogged, damaged, or needs removal for repairs.

The Burner Cap Assembly "C" Matte Blk is an OEM part for Bosch gas cooktops. As the rounded covering fitted over individual burners, it safely contains flames underneath cookware. Maintaining proper cap placement is vital for heating performance and safety compliance standards.

Causes of a bad burner cap assembly can include cracks or punctures from sustained high temperature cycling that compromise its insulating barrier. Over time, surface imperfections like scratches also diminish durability against consistent heat exposure.

Symptoms of faulty caps are:

• Flames improperly escaping from under pan edges
• Visible damage present on cap surfaces
• Inconsistent flame height adjustment or shut-off
• Excessive heat concentration in burnered area

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.