Thermador Parts

This refrigerator ice auger sits inside the ice bin and rotates to move cubes or crushed ice toward the chute. Replacing a worn, bent, or stripped auger restores smooth, consistent dispensing performance. What it does:

• Rotates inside the ice bin to feed ice toward the crusher and dispenser chute
• Helps deliver either cubes or crushed ice depending on the selector
• Common symptoms: dispenser motor runs but no ice comes out, weak/intermittent dispensing, frequent ice jams, or grinding noises from the ice bucket

• 1 ice auger

• Unplug the refrigerator before servicing; remove and empty the ice bin
• Note the order of internal parts during disassembly; transfer any reusable hardware from the original assembly
• Wear cut-resistant gloves—metal and plastic edges can be sharp
• Reassemble so the auger turns freely by hand, reinstall the bin, restore power, and test the dispenser

This refrigerator compressor is the heart of the sealed cooling system. It compresses and circulates refrigerant so the fresh food and freezer sections reach and maintain set temperatures, restoring cooling performance when the original unit has failed.

• Compresses and moves refrigerant through the evaporator and condenser to remove heat from the cabinet
• Restores cooling when a failed or seized compressor is the cause of no-cool/weak-cool conditions
• Symptoms include a warm refrigerator or freezer, extended run time with little cooling
• Clicking or humming from the compressor area with no start, or overheating and cycling on overload

• Sealed-system service requires EPA Section 608 certification, recovery equipment, brazing, deep vacuum, and precise recharging
• Disconnect power and properly recover refrigerant before opening the system; replace the filter-drier, braze with nitrogen purge, leak-test, evacuate, then charge to the specification on the model's data plate
• Transfer any model-specific grommets, brackets, tubing, and external inverter/start components from the original unit or replace as directed in the service manual

This defrost bi-metal thermostat senses evaporator temperature during the defrost cycle and opens to stop heater power at the safe cutoff. Replacing a failed thermostat restores reliable defrosting and helps prevent ice buildup that restricts airflow and cooling.

• Monitors evaporator temperature to control the defrost heater
• Closes when cold to allow defrost; opens at cutoff to terminate defrost and prevent overheating
• Helps maintain clear evaporator coils for proper airflow
• Common symptoms: heavy frost on the back wall/evaporator, poor cooling, or defrost heater not energizing

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator; mount the thermostat in the original location with firm contact on the tubing
• Transfer any original clip or insulation as found to ensure proper sensing
• Secure all connections and route wiring away from the heater and moving parts; clear existing ice before restoring power

This actuator arm is the mechanical lever inside the dishwasher door's dispenser assembly. Working with its spring, it releases the detergent cup at the proper point in the cycle to restore consistent detergent dispensing. What it does

• Transfers motion from the control/drive mechanism to the dispenser latch to open the detergent cup
• Provides the spring tension needed for the lever to return to its home position
• Helps ensure detergent is dispensed at the intended time in the wash cycle
• Common symptoms include detergent left in the cup, a dispenser door that won't latch or opens inconsistently, or a visibly broken/missing lever

• 1 actuator arm with spring

• Disconnect power to the dishwasher before servicing
• Open the door and remove the inner door panel fasteners to access the dispenser linkage
• Note the spring orientation; move the spring to the new arm if needed and seat the arm in the correct pivot location
• Reassemble the door and manually test the dispenser action before running a cycle

Wax motor for detergent/rinse-aid dispenser.

The Burner Cap is an OEM part for Bosch gas cooktops. This small black burner cap safely contains the flame underneath to concentrate heat efficiently for precise cooktop control. Reliable burner caps are crucial for safety, performance, and aesthetics.

Causes of a bad burner cap can include warping or cracking from continuous exposure to high heat over the long run, as well as surface scratching or punctures.

Symptoms of a faulty cap include:

• Flames escaping beyond cap and licking up sides of cookware
• Visible damage or deterioration on cap surfaces
• Inability to adjust flame height as intended
• Burners no longer heating or shutting off properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Replacement bake element for the oven that restores heating for even baking and proper temperature performance. Installs in the oven cavity to provide the heat required during bake cycles. What it does:

• Heats the oven cavity during bake cycles so food cooks evenly.
• Common symptom: oven fails to reach set temperature or food is undercooked.
• Visible symptom: element that is blistered, broken, or shows burn marks may need replacement.
• Electrical symptom: an open (no continuity) element will prevent the oven from heating.

• Always disconnect power to the appliance at the breaker before starting work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Access typically requires removing oven racks and the inner panel; disconnect wiring at the element terminals and secure the new element in place.
• Restore power and test the oven on a bake cycle after installation.

The Burner Head and Cap Assembly is an OEM part for Bosch ranges and cooktops. It contains the burner itself along with its protective cover.

Cracks or misshapen portions disrupt flame stability leading to inconsistent results.

Symptoms of a failed assembly include:

• Irregular or overly high flames from damage exposing gas jets
• Difficulty igniting or flames extinguishing prematurely
• Singed pans lacking the protection of an intact cap

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This outlet hose carries wastewater from the appliance to the household drain. Replacing a cracked, kinked, or clogged hose restores proper draining and helps prevent leaks at the base or under the sink.

• Directs water from the drain pump/sump to the home drain connection
• Common symptoms of a failing hose: standing water after a cycle, slow or no drain, leaks, or visible cracks/kinks
• Restores proper draining when the original hose is brittle, collapsed, or internally obstructed
• Also referred to as a drain hose in many service manuals

• Disconnect power and turn off water before servicing; protect the floor with towels or a tray
• Access both ends of the hose, release clamps, and be prepared for residual water
• Route the new hose like the original, avoiding sharp bends; fully seat and secure all connections
• Run a short cycle and check all joints for leaks after installation

Knob, blk (cvs)

The Control Knob is an OEM part for Bosch ranges and cooktops. As the interface regulating gas flow, control knobs activate precise burner levels through internal calibration.

Causes of failure include loosened set screws beneath allowing knob slippage. Prolonged heat and moisture exposure may also degrade contact surfaces over time.

Symptoms of faulty knobs include:

• Burners failing to engage or not matching dial settings
• Inability to decrease output levels from full flame
• Knobs wobbling insecurely or detaching entirely

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Restore fast, even convection cooking with this rear convection heating element. It supplies a ring of heat around the fan at the back of the oven so temperatures rise and hold properly in convection bake and roast modes.

• Provides heat around the convection fan for uniform air circulation and even results
• Common symptoms: no heat or very slow preheat in convection modes
• Fan runs but temperature does not rise in convection
• Visible damage or a break in the element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely.
• Remove racks; access and remove the element's mounting screws from inside the oven (procedure varies by model).
• Pull the element forward carefully; label and transfer wires one at a time so they don't slip back into the cavity.
• Reuse existing hardware; ensure terminals are tight, reassemble, and test a convection cycle.

This door hinge restores smooth, aligned door operation. Replacing a worn hinge ensures the door opens and closes properly, supports the door's weight, and helps the gasket seal evenly to reduce air or heat loss.

• Provides the pivot point that lets the door open and close smoothly
• Maintains door alignment so the seal sits flush against the cabinet
• Helps prevent sagging, rubbing, or binding at the door edge
• Common symptoms: door drops or won't close flush, squeaks/pops, visible play or hinge damage

• Disconnect power; turn off water supply if applicable
• Support the door before removing hinge fasteners to prevent strain or damage
• Transfer any spacers/bushings from the old hinge to the new hinge if present
• Reinstall and verify door alignment and seal contact; adjust as needed

Located inside the freezer's ice bucket, this ice auger is the helical shaft that rotates to move cubes toward the chute for cubed or crushed ice. Replacing a worn or bent auger restores dispensing and helps prevent jams and grinding.

• Rotates with the dispenser motor to move ice through the bucket and into the chute
• Works with the crusher assembly to provide cubed or crushed ice
• Damage or wear can cause jamming, slow/weak dispensing, or loud grinding during dispense
• Often replaced when the dispenser motor runs but little or no ice is dispensed

• Disconnect power to the refrigerator; remove the ice bucket from the freezer
• Disassemble the bucket/crusher housing; transfer blades, spacers, and hardware to the new auger in the same order and orientation
• Handle sharp metal parts with care; wear cut-resistant gloves
• Reinstall the bucket fully seated; restore power and test both cubed and crushed functions

This door latch and strike plate secure the door closed and engage the safety interlock so the appliance can start and run reliably. Replacing a worn latch restores consistent door closure and prevents nuisance cycle interruptions.

• Locks the door by engaging the strike, keeping it closed during operation
• Ensures the door-closed interlock/microswitch is actuated so cycles can start
• Helps prevent the door from popping open mid-cycle
• Common symptoms: door won't latch or stay closed, unit won't start, cycle stops when the door is jostled

• Disconnect power before servicing
• Open the door and remove the inner-panel screws to access the latch area
• Remove the old latch/strike; align and install the new components
• If your model uses a separate microswitch, transfer/reuse it as required and test door engagement before reassembly

Tall item spray head.
This Spray Head is an OEM part for Bosch Dishwashers. It plays a role in distributing water evenly during the dishwasher's washing cycles. Continuous exposure to hard water, debris, or mineral deposits can cause issues with this component.

What Causes a Bad Spray Head:
Hard water deposits, debris, or mineral buildup can clog or block the spray head, affecting its performance. Physical damage can also impair its functionality.

Symptoms of a Bad Spray Head:

• Inadequate cleaning of dishes
• Uneven water distribution
• Reduced water pressure during washing cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.