Thermador Parts

Small replacement O-ring that seals the dishwasher aqua sensor assembly to maintain a watertight seal and help ensure reliable sensor operation. Fits the sensor housing to reduce leaks and protect internal electronics. What it does:

• Seals the aqua/sensor housing to prevent water from escaping the sensor area
• Helps maintain accurate sensor readings by keeping the sensor dry and properly seated
• Commonly replaced when you see water pooling or dripping near the sensor assembly
• Used during aqua-sensor, pump, or housing repairs where the original seal is damaged

• Always disconnect power and turn off the water supply before starting repairs
• Replace the O-ring only when the sensor or housing is disassembled; inspect mating surfaces for damage or debris
• Ensure the O-ring is seated evenly in its groove before reassembly to avoid pinching or leaks

This LP main jet regulates propane flow to a surface burner to maintain a clean, stable flame. Replace a clogged or incorrect jet to restore proper burner performance, especially when converting a cooktop or range from natural gas to LP.

• Meters LP gas to the burner head for correct flame size and combustion
• Direct replacement for a damaged, clogged, or incorrect jet during service or LP conversion
• May help with yellow/sooty flames, weak or overly high flames, uneven heating, or delayed ignition

• Shut off gas and power; allow the appliance to cool completely
• Remove grates, caps, and burner head to access the orifice holder
• Start the jet by hand, then tighten gently with the correct tool—do not overtighten
• After installation or any LP conversion, leak-test connections and verify a steady blue flame; other jets and the regulator may also require LP settings per the model's instructions

This genuine OEM part is a circulation pump motor for dishwashers. The circulation pump motor distributes water to the spray arm to allow the dishwasher to properly do its job. Over time, the circulation pump motor can become overworked to the point of becoming inoperable. Luckily, replacing the pump motor is not as difficult a job as it might seem. To begin the repair, turn off the power supply and shut off the water supply valve. Remove the screws that secure the lower access panel. Disconnect the water supply line from the inlet valve. Then proceed to remove the mounting screws from the junction box cover. Take note of the wires' orientation. Remove the screws that hold the bracket. Disconnect the drain hose from the sink or garbage disposal. Open the dishwasher door and remove the mounting screws. Pull the dishwasher away from the cabinet and unsnap the covers from the hinge ropes. Disconnect the ropes. Remove the screws securing the upper door panel. Carefully tilt the dishwasher back and detach the fill hose from its retaining clip disconnecting the hose from the sump. Uninstall the circulation pump and align the pump with the seal and sump. Tighten the clamp and transfer the wires from the old pump to the new one. Proceed to reinstall the panels that were uninstalled.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dishwashers.

Replacement spray arm that restores water distribution for better rinse coverage and more even cleaning. Installs in the dishwasher tub to re-establish spray patterns and water flow lost to cracks or wear. What it does:

• Rotates and directs high-pressure jets of water to rinse and loosen food soils from dishes and cookware
• Restores proper spray coverage when the original arm is cracked, clogged, warped, or not spinning freely
• Helps reduce spots and missed areas by re-establishing even water distribution across racks
• Works with the dishwasher's pump and tubing to maintain normal wash performance

• Disconnect power and turn off the water supply before beginning any service
• Remove lower rack and any retaining clip or cap to access the spray arm; note orientation for reassembly
• Inspect and clear spray holes of debris before installing; ensure the arm spins freely after installation
• Do not overtighten mounting hardware; replace any damaged clips or seals for a secure fit

This ignition device generates the spark needed to light gas burners, restoring reliable ignition and preventing continuous clicking or no-light conditions. Replace a failed module to re-establish normal burner ignition. What it does:

• Sends high-voltage sparks to the burner electrodes to ignite the gas flame
• Replaces a faulty spark generator when burners won't light or there is no visible spark
• Stops continuous clicking or rapid sparking caused by a failing ignition module
• Works as the central control for timed spark output to each burner electrode

• Disconnect electrical power and shut off the gas supply before starting any work
• Remove the oven/range access panel and note wire locations or take a photo to ensure correct reconnection
• Handle the electrode and module carefully to avoid bending or contaminating the spark tip

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation

A replacement drain pan that captures defrost and condensation water to keep it contained and away from the cabinet and floor. Restores the appliance's normal water-collection path and helps reduce leaks. What it does:

• Collects melting ice and condensation from the evaporator to prevent water from pooling under the appliance.
• Channels collected water toward the drain system so it evaporates or exits as designed.
• Stops common symptoms like puddles or moisture under the unit and musty odors caused by standing water.
• Fits under the evaporator/coil area to restore proper water management.

• Disconnect power to the appliance before service to avoid electrical hazards.
• Remove the required access panels or move the appliance per the manufacturer's guidance to reach the pan.
• Lift out the old pan carefully—it may contain standing water—and position the replacement so the drain outlet and routing match the OEM layout.
• After installation, restore power and check for proper water flow during a defrost cycle; inspect surrounding seals and tubing for proper seating.

Color: light gray. Measures about 3 inches high by 2 inches deep.

This replacement plate restores the proper mounting/cover surface specified in your appliance's assembly, helping keep components aligned, protected, and secure for reliable operation. Ideal for replacing a bent, cracked, or missing original.

• Serves as the specified support/cover plate within the assembly
• Maintains alignment and a secure fit for adjacent parts
• Replace when the original is bent, cracked, worn, or missing
• Symptoms can include rattling, misalignment, loose components, or visible damage in the plate area

• Disconnect power and shut off gas/water supplies (as applicable) before servicing
• Refer to your model's parts diagram to locate and orient
• Transfer or reuse original fasteners and seals if in good condition
• Hand-start screws and tighten evenly; verify alignment and smooth operation after installation

This sump collects and channels dishwasher wash water into the wash pump, helping maintain proper drainage and reduce leaks at the tub-to-pump connection. Replace a cracked or damaged sump to restore correct water flow and sealing. What it does

• Directs wash water from the tub into the wash pump and drain system.
• Houses the pump inlet and seals the pump-to-tub interface.
• Prevents leaks by providing a secure seal between the tub and pump assembly.
• Common symptoms: pooling water in the tub, dishwasher not draining, leaks from the base, or unusual pump noise/vibration.

• Disconnect power and turn off the water supply before starting any repair.
• Handle carefully; inspect and replace any worn gaskets or seals when installing the new sump.
• Access typically requires removing lower access panels and the lower dish rack.
• After installation, test for leaks and proper drain operation before returning the appliance to normal use.

This is the right side hinge plate. For left side use 00298567.

The Drive Link, Welded Assembly is an OEM part for Bosch range hoods. This assembly is responsible for linking the motion of the internal components to allow for proper function of the range hood.

The Drive Link provides a direct connection between the internal drive system and blower fan, facilitating the smooth transfer of power needed for ventilation. It also helps guide internal mechanisms to ensure components operate as intended with each other during use.

Causes of a bad Drive Link can include wear from continuous use, excessive stress, or damage resulting from impact. 

Symptoms of a bad Drive Link include:

• Reduced or uneven ventilation output
• Strange noises coming from inside the range hood
• Difficulty adjusting ventilation settings or fan speed
• Internal components not functioning in sync

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This gas burner jet holder assembly routes fuel through the orifice to the burner and secures the connection. The red 11,000 BTU version is designated for the right-front or left-rear burner, helping restore proper flame and heat output.

• Positions the jet and routes gas from the manifold to the burner for the specified heat output
• 11,000 BTU, red-coded variant designated for RF/LR burner location
• Provides a stable, serviceable connection between tubing and burner base for a consistent flame
• Symptoms include weak or irregular flame, failure to ignite, or incorrect flame size at the RF/LR burner

• Shut off gas supply and power; allow the appliance to cool before servicing
• Remove grates, burner caps/heads, and any panels needed to access the holder
• Support gas tubing and use two wrenches on fittings to avoid twisting or damage during removal/installation
• After installation, check all joints with an approved leak-detecting solution and verify flame quality

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This jet holder secures the jet/nozzle assembly, keeping it correctly positioned for consistent flow and performance. Replacing a cracked or loose holder restores proper alignment and helps prevent leaks, drips, or irregular spray from the outlet.

• Holds the jet/nozzle firmly in place to maintain directed flow
• Keeps the jet aligned for even, reliable output
• Helps seal the connection to reduce drips at the fitting
• Typical symptoms: loose or missing jet, visible cracks, leaks, weak or erratic spray

• Disconnect power and shut off the applicable supply to the appliance before servicing
• Access the jet assembly and note the holder's orientation for correct reinstallation
• Inspect any O-rings/seals at this connection and replace if worn or damaged
• Reassemble carefully and avoid overtightening; test for proper flow and no leaks

This Filter is an OEM part for Bosch Range Hoods. It plays a role in maintaining clean and purified air in your kitchen by trapping grease, smoke, and odors during cooking.

What Causes a Bad Filter:
Over time, the filter accumulates grease, dirt, and particles from cooking, causing it to clog and reduce its effectiveness. Additionally, if the filter is not cleaned or replaced regularly, it can become damaged or deteriorate.

Symptoms of a Bad Filter:

• Reduced airflow in the kitchen
• Lingering cooking odors
• Poor grease and smoke absorption

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.