Thermador Parts

This is a baffle-style air filter kit designed for use in a range hood or vent hood. It captures grease and airborne particles generated during cooking, helping to keep the ventilation system clean and functioning properly. Replace this filter if you notice reduced airflow, excessive grease buildup, or lingering cooking odors in your kitchen.

Left side door hinge plate for your dishwasher. Replaces cracked, broken, or worn hinge plates that cause door misalignment or instability.

This TH capacitor is an electrical control-circuit capacitor used on compatible Bosch appliances to help stabilize voltage and filter electrical noise for reliable control-board operation. Replacing a failed capacitor can address intermittent control issues. What it does

• Stabilizes control-board voltage and helps filter electrical noise that can cause erratic behavior.
• Supports reliable startup and operation of control circuits.
• Common symptom link: intermittent or unexplained control-board errors, erratic or non-responsive controls.
• Common symptom link: appliance displays control or error codes related to electronics or intermittently fails to start.

• Disconnect power to the appliance at the breaker before servicing to avoid shock.
• Discharge any capacitors and allow boards to sit before touching components; use appropriate ESD precautions.
• Only replace with the exact part number; confirm orientation and connector fit before reassembly.

Pressure regulator for gas cooktops maintains consistent gas flow to burners. Replace if leaking gas odor, damaged vent, or worn seals detected.

Exterior front panel that restores your dishwasher's appearance. Replaces dented, scratched, or corroded panels. Covers and protects inner components.

This burner base supports the cooktop's burner cap and directs flame for even heating. It replaces a damaged or warped base to restore stable burner alignment and consistent flame pattern. What it does:

• Holds the burner cap in place and centers the gas flame
• Channels gas flow for proper burner operation
• Helps prevent wobbling or uneven heating from a warped base
• Commonly replaced when the base is cracked, corroded, or bent

• One burner base (B)

• Turn off gas supply and power to the appliance before servicing
• Remove surrounding burner components and reassemble in reverse order
• Inspect nearby seals and burner ports for damage; replace if necessary

Rounded cap that sits over your gas cooktop burner to contain and direct flames. Replace if cracked, chipped, warped, or worn from high heat exposure.

Black burner cap assembly that covers and protects the gas burner head. Replace if your cap is cracked, chipped, damaged, or missing to restore appearance.

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

Replace a worn, broken, or missing gas range control knob. Restores safe operation and improves appearance. Fits directly onto the control shaft.

Replace a cracked, chipped, or missing microwave turntable plate. This glass dish installs on the drive roller to restore the rotating cooking surface.

Repair set for dishwasher rack rollers. Restores smooth rack movement when wheels are broken, cracked, or worn. Installs on upper or lower racks.

Microwave not heating? A failed diode rectifier prevents proper power flow to the magnetron. This one-way current component is essential for heating function.

Secures the filter assembly in your range hood. Replace when the original spring is worn, bent, broken, or missing to restore proper filter fit and seating.

This genuine replacement pushbutton knob restores a damaged or missing control knob so you can operate your appliance's push-to-select controls easily and reliably. It matches the original shape and finish for a clean, factory look. What it does

• Replaces a broken, cracked, or missing pushbutton knob to restore button-tactile control
• Provides the correct fit and engagement for the appliance's panel-mounted pushbutton switch
• Helps prevent dirt and debris from entering the button assembly
• Matches factory color and finish for a consistent appearance

• One white pushbutton knob

• Disconnect power to the appliance before starting any repair
• Most installs are simple: pull off the old knob and press the new knob onto the button shaft until it seats
• If needed, use a small flat tool gently to lift an old snapped piece;

Secures internal components to the range frame. Replace if bracket is cracked, broken, bent, or missing to restore proper alignment and stability.