Wall Oven Parts

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

The drip pans I ordered fit my stove perfectly. I was extremely happy. I had tried drip pans from Wal Mart and Lowe's and they wouldn't sit right in the stove. Read more

• Oven not heating evenly
• Little to no heat when baking

Checking for part replacement.....found your website.....I thought I had the right part, but called the tech/order line. Spoke to a very knowledgable tech, which she checked the stove serial # vs the part I thought I could use. The Tech advised that it WAS NOT and related the findings. I agreed after a short discussion and ordered the new element. The order was placed on Monday afternoon, on TUESDAY the FEDX truck pulled in with the replacement element!!!!!!! I watched the video offered on... Read more

Replace 2 switches. Read more

• Won't start
• Element will not heat

I ordered the recommended Infinite Heat Switch Kit and Element Receptacle and Wire Kit and installed them. The latter was a breeze, appearing to be exactly the same as the original, except for the wire color. The switch, though, was another story. It is a RobertShaw "replacement" part, designed, it seems, for use in the greatest number of original units as possible. The most obvious difference between this switch and the original (besides its comparatively small size) is the long, segmented... Read more

• Oven is too hot
• Oven not heating evenly
• Won't start
• Little to no heat when baking

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

Orded rack by stove model number. fit perfect Read more

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

The most difficult part was figuring out how to take the door off as the manual instructions were not clear. Thank you, YouTube for your help. This door doesn't have the more modern release latches. You open the door all the way and stick Allen wrenches into the holes that appear by the joint of the latch. When you close the door to 3/4 or 7/8 closed, the latches are released from the unit and by holding the sides of the door, you pull it out. The whole replacement would take around an hour,... Read more

Replaced the switches. Read more

• Element will not heat

Watched the video when the part came, and 5 minutes later, our 25 year old stove is once again working like a champ. Read more

So, after looking for replacement parts, I found these. I was delighted. My original knobs were plastic with a silver finish. They had blistered from the heat of the stove over the years. The replacement knobs were all metal. Price was right. Very happy. Read more

I fallow instruction by watching video Read more

Cleaned/ soaked all burners in Ammonia and scraped off the remaining with a pumice stone. Oiled all screws. Replaced (4) ignitors or electrodes and module kit/ right front burner/ burner switch harness. Although this was the third order of switches from 3 different places including the local supplier due to the switches being manufactured upside down and lit on low on the first attempt. (Since I was going to have to open it up again to either repair or remove and return the upside-down harness... Read more

• Won't start

Replaced srark module Read more

Order the part to ApliancePartsPro and within 3 days I had it delivered to my front door. Looked up in their help page and was guided how to do it. It was so ease . I will recomend all my friend to get their parts at ApliancePartsPro. I am very please with the service and quality. Read more