Wall Oven Parts

Replaced the regulator with part #AP5802175. Watched the video when purchasing, and it was spot on. Would have taken me about 15-20 minutes if I had access to a vise, to remove one of the fittings. Was able to get it out using two wrenches, but it was not without a bit of elbow grease. The new part went in easily. Turned on valve on regulator, plugged in the power, turned on the gas valve, done. Everything worked fine. Easy job for anyone with just a few tools. Read more

My Granddaughter fixed in about 5 minutes, she was proud and I was happy. Read more

The problem seemed to be with the switch so I watched a few youtube videos to learn more about how ranges work. After locating the correct replacement switch I ordered it on-line around 10 pm Tuesday night. The new switch arrived Thursday morning at about 10 am and I had my range back up and working like new in less that 30 minutes. The hardest part was figuring out how to remove the slide in panel to access the switch. There were plastic washer/nuts behind each know which I was able to... Read more

Took it apart and replaced it. Read more

First temp probe,then control board Read more

Bought a replacement gasket. Read more

It was a very quick repair that took less than 5 minutes to fix. Read more

Replaced the oven heating element Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• Element will not heat

This repair was on a GE glass Cooktop range. This range has two indicator lights, a Burner On light, and a Hot Cooktop Light. The problem I was having was, the Hot Cooktop stayed on all the time (24x7), even when the cooktop surface had been off for hours and was cold. YouTubes that I viewed were all misleading on this symptom. They all pointed to the switch, which is the fix for the Burner Light staying on, not the Hot Cooktop Light staying on. I figured it out by going to the schematic.... Read more

I found the model and serial #'s. Looked them up on your website. You provided a diagram with part numbers. I ordered the parts. Your website made it extremely easy. Thank you. Read more

I googled the error code and symptoms my oven was exhibiting to determine the solution and which parts to order. I needed a new control panel and chose also to replace the overlay that shows on the front of the stove. I could have reused the old one because I turned out to be able to remove it without damaging it. I just kept it in case I damage the new one in the future. The “fast” shipping (not overnight) option had the part delivered the next morning, which was a nice surprise. I felt... Read more

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

Replaced the oven control board. Read more

Initially, I took it off, sanded it and painted with appliance touch-up. Still didn't look good so I ordered a replacement part and installed. Read more

So initial thought was bad bake igniter. I'bve replaced this before so I replaced it again and it wouldn't glow. Checked broil igniter and same thing, no glow. Checked voltage at molex connector for bake igniter and it went from 6.6v to 3.4v when triggered to glow -- well below the 120v expected. Ordered new clock/controller and overlay -- it shipped the next business day! Removed a handful of screws from the back panel to expose the clock/controller and removed/ replaced it with new... Read more