Need Help?
Call
If your cooktop burner won't heat or won't adjust temperature, the infinite switch likely failed. This part regulates burner power. DIY repair in 30-45 minutes.
Removed control panel and replaced broken switch. Much easier then expected. Read more
The Rocker Switch is an OEM part for GE ranges. This switch is used to control the surface heating elements, allowing users to turn them on or off and adjust the heat levels. It is designed to fit securely into the range's control panel, providing reliable operation and ease of use.
Causes of a bad switch rocker element can include regular wear and tear, electrical issues, or damage from spills or high temperatures. Over time, the internal contacts of the switch can degrade, leading to malfunction.
Symptoms of a bad switch rocker element include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Replaced the switch took a total of about five minutes. I pulled the stove out and turned the breaker off so I only had to pull it out enough to get a 1/4 " nut driver in behind it. Removed three screws and the back cover came off. I pushed the switch threw from the back and switched over the two wires then reversed the process. Completely easy if you can use a screw driver your crazy not to replace it yourself Read more
Burner won't spark or ignite? This spark switch signals the ignition module to light gas burners. Common DIY repair with basic tools, 15-30 minutes.
Took out igniter module and porcelain was cracked. Replaced with ordered part and it worker fine! Read more
Burner not heating or stuck on? This surface element switch controls power to individual cooking elements. Moderate DIY repair requires lifting cooktop.
Burner overheating or stuck on high? This infinite switch regulates temperature by cycling power on and off. Common fix for unresponsive heat control.
I had one element that would operate wide open when turned on the low setting. It needed the switch replaced. Since I was replacing other elements I went ahead replaced them all, adding new drip pans and wiring kits to each new element. Once I replaced everything I was still having issues with the element that had the switch replaced. After further investigation my AC voltage readings were not correct at this element. I traced the problem back to the Molex connector feeding voltage to the... Read more
Fix burners stuck on high or not regulating temperature with this range infinite switch. Controls heating element power for precise cooking control.
Using the video on your site I was able to make the repair. It was a pretty straight forward repair. Thanks for having the diagram on your site for helping me find the right part. Read more
Fixes burner stuck on high or no heat issues. This infinite switch regulates cooktop element temperature by cycling power on and off. Simple replacement.
Just a simple install my maintenance man just put it in with no problems. Read more
If your cooktop burner is stuck on high or won't adjust temperature, the infinite control switch likely failed. This part controls heat levels.
The parts are under the stovetop and the knobs are attached to them. We bought the correct ones from AppliancePartsPros, these were the correct ones. Seems we have an oddball stovetop. It's a GE drop in stove. The parts were easy to change. It was a simple matter of putting the wires on the new switch in the same place there were on the switch. I took phone pics of the wire locations before I took them off and only did one switch at a time. Turn the power off at the breaker panel first of... Read more
Burner won't heat or stuck on one temperature? This infinite switch controls your range surface element heat levels. DIY repair restores precise cooking.
I was able to clean the Oven Temp Sensor with 99% alcohol. Then replaced All switches (after breaker was isolated). Put it all back the way I found it. Turned on breaker. Tested all functions and had no reports of Fan Code re-appearing since. Read more
If your range burner won't turn on or off properly, or the indicator light stays on when turned off, this infinite switch restores control. DIY repair.
Remove front panel and replaced. Received parts fast. Read more
Fix burners that won't spark or click constantly. This igniter switch wiring harness restores reliable lighting on gas ranges. DIY-friendly repair.
I replaced the switch/wire harness that connects to the gas valves. Read more
The Dual Element Surface Switch is an OEM part for Frigidaire electric ranges and cooktops. It governs power distribution to the dual element.
Causes may be loose electrical terminals within the switch, defects from past power surges, or general wear over extended use.
Symptoms of a bad surface switch include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
I replaced both the large single element and the large dual element control switches. It appears the resistors were burning out. Problem seems to be fixed. Will know later when I do some simmering. Read more
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more
Provides electrical connection and control for gas burner ignition on cooktop surfaces. Replace if burners won't light, produce weak sparks, or if you hear clicking without ignition.
I called a rpair service. The men came to the house, torn apart the stove top and advised Replacement of the wire harness. The trip charge of $100 would be deducted from a repair bill of $350, thus they needed an additional $150 for parts and $100 for labor after paying the trip charge. I bought the harness for $60, and the star bits I needed for my drill for $10. My son and I installed the new harness in about 30 minutes, which included a thorough cleanup, saving us $180. Read more
Fix a burner that won't turn off or heat properly with this dual infinite switch. Controls both inner and outer element rings. Moderate DIY repair.
Relatively easy DIY Read more
Burner won't spark or click when you turn the knob? This igniter wiring harness restores the electrical connection between switch and igniter. 30-minute DIY fix.
My husband and myself didn't agree on which part was the exact problem. He felt it was the valve. I felt it was the ignitor/ orifice. And we both agreed the Harness-Ignitor needed to be replaced. So we ordered all 3, and I'm not sure if in fact all three were needed or not, but now with those parts replaced, the range is working like brand new!! Thanks to all the videos and diagrams on the website we were able to fix it ourselves easily. And the price was cheaper then other websites, also it... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.