White Westinghouse Washer Parts

The Washer Drain Hose is an OEM replacement part for Frigidaire washing machines. It is a flexible, 7 ½ ft plastic hose that connects the washer tub to the household drainage system. The drain hose removes water from the washer at the end of each cycle.

Symptoms of a faulty drain hose include:

• Water failing to fully drain or continuously draining
• Wet  flooring around the washer due to leaks
• Excess water left standing in the washer tub after cycles
• Reduced washing performance due to inadequate drainage

Causes of a bad drain hose include kinks or bends that restrict water flow, cracks or holes from wear and tear, and blockages from accumulated debris. These issues can compromise the hose's ability to drain water properly.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Agitator Hub is an OEM part for Frigidaire washing machines. It connects the agitator to the drive shaft, enabling the agitator to rotate and move clothes effectively during the wash cycle.  

Causes of a bad agitator hub can include wear and tear from frequent use, exposure to harsh detergents or hard water, or damage from overloading the washer.  

Symptoms of a bad agitator hub include:

• Agitator not moving or rotating properly
• Loud noises or grinding sounds during the wash cycle
• Clothes not being cleaned effectively
• The washer shaking or vibrating excessively

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This agitator is a genuine Frigidaire part, sold individually. This agitator can be used as a replacement part for a washing machine or a washer/dryer combination appliance. This part rotates within the tub of the washing machine so that clothes and other items are tumbled around and fully cleaned.If an agitator has been subject to damage at some point in the standard lifespan of a washing machine, symptoms of damage will manifest in the form of a washing machine that will not agitate in a normal laundry cycle. If this is occurring, the agitator should be inspected for visible signs of damage, including punctures, scrapes, tears, and erosion to the material that could preclude it from serving its function. If the agitator seems damaged upon assessment, it should be removed and replaced with this genuine OEM replacement part before using the washing machine again.This is an OEM part sourced directly from the manufacturer. It is sold individually. This agitator is compatible with the following appliance brands: Frigidaire, Kenmore, Gibson, and Kelvinator.

The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:

• Secures and centers the spin basket on the drive shaft for balanced rotation
• Transfers drive torque to the inner tub during spin
• Helps maintain basket alignment to reduce vibration
• Typical symptoms of failure: loose/wobbly tub, scraping or grinding noises, poor or no spin, frequent out-of-balance events

• 1 trunnion

• Disconnect power and water before service; wear gloves and eye protection
• Access the hub by removing top/access parts, then the agitator/wash plate and inner-tub fasteners
• Clean the shaft and mating surfaces; seat the new trunnion fully and tighten fasteners evenly in a crisscross pattern
• Inspect related parts (tub seal, bolts, bearing) while open and replace if worn; run a short test cycle to ensure smooth spin

This is a transmission assembly for washing machines. The transmission assembly is the gearbox in the washing machine's motor that allows the washing machine to work at different speeds and different intensities. If the washing machine is no longer spinning properly and has lost its normal level of washing power, it could mean that the transmission assembly needs to be replaced. Luckily, replacing this part is not as difficult as it might seem at first glance.To replace the transmission assembly, begin by unplugging the washing machine. The first step is to remove the upper control panel. Pull forward on the bottom of the console and remove the two retaining clips as well as the harness connector to the lid switch. Using a flathead screwdriver remove the clips. After this, remove the entire cabinet from the back panel to gain access to the interior of the washer. Remove the 7/16 bolt from the agitator and pull it straight up to remove it from the shaft. Once completed, gain access to the motor and pump and remove by releasing the screws and tabs that attach it. Remove the wire harness attached to the transmission. Remove the bolts that secure the motor mount to the transmission and proceed to pull the old transmission out of its place. Install the new transmission and reassemble the other parts.This genuine OEM replacement part is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse washers. It is sold individually.

Outer door panel that replaces a damaged or worn outer door surface, restoring the appliance's finished exterior and protecting inner door components. Ideal when the exterior is dented, scratched, or cosmetically damaged. What it does

• Provides the finished exterior surface for the appliance door and protects internal door components from damage.
• Restores appearance after dents, scratches, rust spots, or cracked paint.
• Re-establishes mounting surfaces and edge trim where tabs or attachment points are intact.
• Helps prevent further corrosion or moisture intrusion into the door assembly.

• Disconnect power (and water, if applicable) and follow before starting; use proper PPE.
• Door removal and panel replacement often require basic hand tools; save and reuse original screws, handles, and trim unless replacements are supplied.
• Transfer any hardware, insulation, or inner-door pieces from the old door to the new panel as required.
• Large panels can be awkward—have a second person assist to avoid dropping or bending the panel.

This 115V water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water supply when the valve fails. Designed to replace a faulty solenoid valve and stop leaks or no-water issues. What it does

• Opens and closes water flow to the ice maker and door dispenser when energized.
• Commonly replaces valves that hum, leak, or fail to allow water flow.
• Stops intermittent or no-water conditions caused by a stuck or electrically failed valve.
• Works with the fridge's control signals to deliver water only when needed.

• One 115V water inlet (solenoid) valve as shown.

• Disconnect power and shut off the household water supply before replacing the valve.
• Verify electrical connections and water line fittings are tight and leak-free after installation.
• Handle inlet fittings carefully to avoid damage; use appropriate tools and avoid overtightening.

This is a genuine OEM timer that can be used with different models of washers and has been manufactured by Frigidaire. This part has been sourced directly from the manufacturer to ensure the highest possible quality.This timer is critical for the dryer to run properly as it controls the electrical components to enable the correct duration of the washing machine's cycles. If the timer is broken, the washing machine may not run for the intended amount of time or, in some cases, might not function at all. In such instances, the timer will need to be immediately replaced. The appliance will need to be completely disconnected from all power and water sources before repairs are undergone and work gloves should be worn to prevent injury.This timer is sold individually and is manufactured from high-quality, durable, non-corrosive materials. It is an authentic replacement part and compatible with a variety of models of washing machines that have been made by Frigidaire, Electrolux, Gibson, and Kelvinator.

This replacement upper agitator restores the washer's normal wash action by moving clothes and improving water circulation for better cleaning. It fits the factory agitator location and replaces worn, cracked, or damaged agitators to restore performance. What it does:

• Rotates during the wash cycle to move garments through the water for more effective cleaning
• Promotes water flow and prevents clothes from bunching or tangling
• Replaces a cracked, broken, or excessively worn agitator that causes poor wash results
• Helps reduce unusual noise or vibration caused by a damaged agitator

• One upper agitator

• Disconnect power and water supply before beginning any repair
• Remove the agitator cap/cover and securement (bolt or clip) to lift out the old agitator
• Install hardware to manufacturer torque recommendations
• Run a short test cycle with a small load to check for leaks or vibration