Whirlpool Cap Or Cover

Access panel cover for laundry center. Replaces cracked, broken, or missing covers that expose internal components. Secures cabinet opening for clean look.

Outer housing cover for refrigerators. Protects internal components and seals the cabinet. Replace if cracked, broken, or missing to restore enclosure.

White right-hand hinge cover for bottom-mount refrigerators. Replaces cracked, broken, or discolored hinge covers to restore a clean appearance.

This cap or cover installs on your dryer to protect internal components and maintain a finished appearance. Replace if cracked, broken, or missing.

Replace a cracked, broken, or missing evaporator cover in your refrigerator. This plastic cover installs over the evaporator coils in the freezer section.

Plastic evaporator cover for refrigerators. Installs over the evaporator coil in the freezer section. Replace if cracked, broken, or missing.

Control panel cover for laundry center units. Replaces cracked, broken, or missing covers that expose internal components. Installs on the top panel.

This replacement door restores a secure close and proper sealing for your appliance. Replacing a damaged or misaligned door helps ensure safe operation and correct latch/switch engagement for reliable everyday use. What it does:

• Provides the closing barrier for the appliance cabinet to maintain proper containment (heat, air, steam, or moisture as designed)
• Aligns with hinges and latch/door switches for correct interlock and operation
• Helps prevent leaks and drafts and protects the interior from damage
• Can address issues such as difficulty closing, visible cracks/dents, poor sealing, or the unit not starting/stopping when the door is moved

• Includes 1 door

• Disconnect power before servicing; also shut off gas or water if applicable
• Support the door during removal/installation; a second person may be needed for larger/heavier doors
• Transfer any reusable hardware (hinge pins, screws, nameplate/trim) from the original as needed
• After installation, verify alignment, latch engagement, and seal/gasket contact; test operation

• Finish, handle style, and configuration are model-specific—ensure the correct match

This washer lid assembly replaces a cracked, broken, or misaligned lid so the washer can close and lock correctly, restoring safe operation and reducing cycle interruptions caused by a lid that won't align or latch.

• Covers the tub opening and aligns with the lid lock/strike for proper engagement
• Restores the safety interlock so wash cycles can start and run without interruption
• Helps contain splashing and keeps debris out of the washer when not in use
• Typical symptoms include visible cracks or shattering, warped or loose lid, broken hinge area, or intermittent lid-lock errors

• Disconnect power before servicing
• Protect the cabinet surface and support the lid during removal/installation to prevent damage
• If required by your model, transfer existing hinge hardware and fasteners to the new lid
• After installation, check alignment and ensure the lid lock engages smoothly before running a cycle

This replacement pusher fits the refrigerator's ice dispenser/ice-bucket assembly and helps drive the mechanism that moves ice through the chute. Replacing a worn or broken pusher restores smooth, reliable ice dispensing.

• Engages the dispenser/crusher linkage to advance ice from the bucket toward the auger and chute
• Supports crushed/cubed selection on models equipped with that feature
• Wear or breakage can cause weak or no dispensing, jamming, or being stuck in one mode
• Visible cracks, deformation, or missing plastic are common failure signs

• Disconnect power to the refrigerator; remove the ice bin
• Access the ice bucket/dispenser mechanism and note the original pusher's orientation before removal
• Reuse existing screws/clips as needed and confirm the mechanism moves freely after installation
• Reinstall the bin, restore power, and test both cube and crush dispense modes

Replacement pusher for food processor feed tube. Guides ingredients safely into the blade assembly. Replace if cracked, broken, or missing for safe operation.

Replaces a cracked, warped, or missing cover on your refrigerator. Protects internal components and restores proper fit so parts stay secured.

Conceals and protects the refrigerator door hinge area. Replaces cracked, missing, or loose hinge covers to restore clean appearance and shield components.

Encloses the blower wheel and seals the housing for efficient airflow. Replace if cracked, broken, or missing to restore proper air movement.