Whirlpool Hinge Parts

Right hand side. For screws use WPW10119828.

White door stop that limits how far your refrigerator door swings open. Replace if broken, cracked, or missing to prevent door overextension and damage.

This door hinge supports and pivots the appliance door for smooth, aligned opening and closing. Replacing a worn hinge restores proper closing and helps the latch and door seal make consistent contact. What it does:

• Provides the pivot point and structural support for the door
• Maintains door alignment for correct latch engagement and seal contact
• Helps prevent binding, sagging, uneven movement, and squeaks
• Common fix for doors that won't close fully or feel loose/wobbly
• Replaces hinges that are bent, cracked, or show excessive play

• 1 door hinge

• Disconnect power (and shut off gas/water if applicable) before servicing
• Support the door to prevent strain; removal may be required to access the hinge
• Remove hinge cover/trim and mounting screws; transfer any hardware to the new hinge
• After installation, verify alignment and closure; adjust as needed for proper latch and seal contact

Replacement door hinge assembly that secures and supports your refrigerator door. Restores smooth pivoting when the original is cracked, worn, or broken.

Replacement hinge pin that acts as the pivot point for your refrigerator door. Install when the original pin is worn, broken, or missing.

Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.

Replace a worn, cracked, or broken microwave door hinge to restore smooth door movement and proper alignment. Ensures the door opens, closes, and seals.

Right-hand door hinge assembly for dryers. Installs on the door panel to restore proper alignment and smooth opening. Replaces cracked, worn, or broken hinges.

Replaces a broken or worn top left door hinge on your refrigerator. Secures the door to the cabinet for proper alignment and smooth pivoting movement.

Nonmetal shim that maintains proper spacing and alignment in refrigerator hinge assemblies. Replace if worn, missing, or cracked to prevent vibration.

Replacement door hinge for dryers. Supports and pivots the door to keep it aligned during opening and closing. Replace if cracked, broken, or worn.

Top door hinge assembly for refrigerators. Mounts at the upper door pivot point to support and align the door. Replace when bent, worn, or broken.

A hinge pin assembly that secures and aligns an appliance door to its cabinet, restoring proper fit and smooth opening and closing while reducing hinge noise. What it does:

• Secures the door pivot and maintains proper door alignment for a consistent seal.
• Can correct door sag, uneven gaps, or doors that stick, scrape, or fail to close fully.
• Can reduce grinding, clicking, or binding noises caused by worn or bent hinge pins.
• Replaces worn, broken, or bent hinge components that affect door motion.

• Disconnect power to the appliance before beginning any repair.
• Support the door (use a helper or suitable block) to prevent it from dropping when removing the hinge.
• Basic hand tools are typically required; follow the manufacturer's service instructions for safe removal and reinstallation.
• Inspect adjacent hinge mounts and fasteners during installation; replace damaged mounting hardware as needed.

This cam door replaces the small plastic cam that guides and supports the appliance door mechanism, restoring proper door alignment and secure closing so the appliance can latch and operate reliably. What it does:

• Guides the door or door strike into the correct position during closing
• Helps the latch engage so the appliance recognizes the door as closed
• Replaces worn, cracked, or broken cams that cause misalignment or noisy operation
• Can stop symptoms such as a door that won't seat, rattles when closing, or prevents the appliance from starting

• One cam door (single replacement cam)

• Disconnect power (and water if applicable) before starting any repair
• Remove the door or access panel per your model's service instructions to reach the cam
• Verify cam orientation and engagement with the latch/strike before final assembly

Adjustable door hinge and cam assembly for refrigerators. Installs on the door frame to provide smooth opening and closing. Replace if cracked or worn.

Secures the refrigerator door at the top while allowing smooth opening and closing. Replace if the hinge is cracked, broken, or worn from years of use.