Need Help?
Call
Fix a washer that won't advance cycles or stops mid-cycle with a new timer control. Common DIY repair taking 10-15 minutes with basic tools.
Watched the video , perfect instructions, part on time, right part , took 10 min to replace Read more
Fix a washer that won't advance through cycles or gets stuck between wash and rinse. This cycle switch controls your wash sequence. DIY repair.
Ordered the right part, took the back off the top control panel, and popped it in. Read more
Fix washer not filling, slow fill, or water leaks with this water inlet valve assembly. Moderate DIY repair, typically takes 30-60 minutes to install.
I replaced the water inlet valve assembly. We have relatively hard water and I assumed that over the years those inlet valves were clogged with calcium deposits which in turn led to the high pitched squealing as water was added to the machine. The hardest part of the entire job was releasing the top of the washer to disconnect the hoses from the valve assembly. Everything else was relatively easy. We simply followed the online video. My washer no longer screams and I'm thrilled! Your... Read more
Plastic bearing that mounts to the wash tub and supports smooth lid movement. Replace if cracked, worn, or missing to restore proper lid operation.
Watched a YouTube video. Read more
If clothes aren't moving during wash cycles or agitator spins freely, this vertical post replacement restores proper wash action in top-load washers.
Installed a replacement Read more
White decorative bezel that covers the lid lock mechanism on top of your washer. Replace if cracked, scratched, discolored, or missing from wear.
This fabric softener dispenser assembly stores the softener and releases it at the proper time in the rinse cycle. Replace a cracked, clogged, or missing dispenser to restore reliable dispensing and help prevent leaks or residue.
This company is great & I highly recommend it to anyone. I was beyond pleased with the customer service when I called to order my part. The price was unbelievably cheap. I ordered it on Friday at 5:00 pm & it was delivered less than 24 hours later! I will definitely use A.P.P. again. Read more
Spring installs inside the gas pressure regulator assembly on gas dryers. Replace if lost during conversion between natural gas and propane fuel types.
Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more
This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
Fixes broken or cracked detergent drawer that won't stay in place. Simple 5-minute replacement—just pull out old drawer and snap in new one.
Had to buy a new draw handle and detergent draw..they attach together by two plastic tabs that take a lot of stress each time you open it..unfortunately had to buy both to fix the problem.. Read more
Washer only fills with hot water or stops mid-cycle? The water temperature switch controls incoming water temps for proper cycle selection. DIY repair.
I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more
Washer won't spin or agitate? Drive motor powers the wash and spin cycles. Common fix for humming motor that won't start or burning smell issues.
Installed new motor with a metal pulley from APP and VIOLA! Great service, support and inventory. HIGHLY RECOMMEND! Read more
This is a control knob used on a dryer to select cycle settings or timer functions. It fits onto the control panel shaft and allows you to turn and select the desired drying cycle. Replace this knob if it is cracked, broken, or no longer grips the shaft properly, making it difficult to start or change dryer cycles.
Ordered a new one Read more
This is a metal hinge support plate that reinforces the door hinge area on a dryer, helping to secure the hinge to the front panel or door. It distributes the stress of repeated door openings across a wider area to prevent damage. Replace this plate if the dryer door sags, feels loose at the hinge, or if the mounting area around the hinge shows signs of cracking or wear.
Replaced several hinge parts. Read more
If your washer agitator won't move or clothes aren't getting clean, this agitator assembly restores wash action. Simple DIY repair in minutes.
It was fairly simple, unbolted the agitator and pulled the old one out then put in the new...although when when a load became unbalanced the rocking motion slowly strips the bolt, I would suggest if replacing this unit also order the bolt. I also bought loctite dew to the fact that the bolt was stripped. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.