Need Help?
Call
Leaking from the water inlet connection? This vacuum break prevents backflow and maintains the air gap at the inlet. Easy DIY fix in under 30 minutes.
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and... Read more
Fix slow filling or loud screaming noises during wash cycles. This water inlet valve controls flow into your washer tub. Moderate DIY repair.
Replaced inlet valve Read more
This water inlet valve controls the flow of hot and cold water into the washing machine tub during fill cycles. It contains solenoid-operated ports that open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it shouldn't.
Replaced water inlet valve Read more
This assembly includes the dispenser housing along with integrated hot and cold water inlet valves for a top-load or front-load washing machine. It controls the flow of water into the machine and routes it through the detergent and fabric softener dispensers. Replace this assembly if the washer is not filling with water, fills slowly, leaks at the inlet connections, or if the dispenser is not properly directing water to the wash tub.
Maytag Bravos Washer, Model #MVWX550XW1 My washer was emitting a loud noise - I describe it as a loud whining noise - while filling with water. The noise seemed to be coming from the fill valve assembly: 1) jiggling the supply hoses changed the inflection of the noise, 2) turning on the faucet in the adjacent laundry tub (thereby reducing the water supply pressure) also diminished the intensity of the whining noise. I ordered and installed this part - No. AP6023337 "Housing". The installation... Read more
Fix washer water leaking into tub or slow dripping when off. Water inlet valve assembly replacement stops fill valve leaks. Easy DIY repair with video.
I ordered from this company expecting the parts to be later than they said and the parts showed up in 2 days like they said. Just before the Easter holiday even. Amazingly fast. Very satisfied!!! Washer is up and running again. Great job on getting me my parts! Thank you! Read more
This is a water inlet valve that controls the flow of water into the washing machine during fill cycles. It is an electrically operated valve that opens and closes to allow hot or cold water into the tub as directed by the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
Ordered this part and just changed it out. Not hard once I figured out how to get in to it. Read more
This is an electrically operated water inlet valve assembly with a built-in vacuum break (backflow preventer) for a washing machine. It controls the flow of hot and cold water into the wash tub when the machine fills during a cycle. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when it should stop, or if you notice water leaking from the valve area.
New valve. Read more
This is an electrically controlled water inlet valve that opens and closes to allow hot and cold water into the washing machine during the fill cycle. It is activated by the washer's control board or timer to regulate water flow at the correct times. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when turned off, or leaks from the back of the machine near the hose connections.
I called AppliancePartsPros to find a replacement water inlet valve. They talked me through finding the clothes washer model number. Once the model number was located, the AppliancePartsPros person on the phone found the correct replacement valve. I received the valve 3-5 days after ordering. I downloaded the clothes washer repair manual and watched some YouTube videos regarding valve replacement. I followed the steps in the repair manual being careful to mark anything I had removed during... Read more
This water inlet valve controls the flow of water into the washing machine during fill cycles. It uses an electrically operated solenoid to open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
The problem wasn't a blocked screen. I took apart my washer. Very easy on the Kenmore 600 series. Before I did this, I watched a YouTube video and it was a piece of cake. The whole job took me 35 minutes. Read more
Fix continuous water flow or won't-stop-filling issues with this washer hot water inlet valve. Controls hot water during fill cycles. DIY-friendly, 30-minute repair.
After researching on line I was able to narrow down the problem to either the cold water of hot water fill valve. These valves are electronically controlled and can go bad thus causing the washing machine to not fill properly. Nf stands for "no fill". I replaced the cold water valve first which was held by two screws and a couple of wires. It literally took me 5 minutes to replace the part. As soon as I started the wash cycle I could tell I had fixed the problem because the humming noise that... Read more
Fix washer that won't fill, shows OE/NF error, or keeps running water even when off. Cold water inlet valve replacement takes 5-10 minutes with basic tools.
Fix washer not filling, slow fill, or LF error codes. This water inlet valve controls water flow into your washer. Moderate DIY repair, 30-45 minutes.
REPLACED ENTIRE WATER CONTROL SYSTEM. Being quite anal about my planning projects, I played a Youtube video about this job. I screen captured the important steps, printed them out and taped above the washer. It was a good approach because it gave me a valid reference of the wiring harness reinstallation. Overall, the project was easier than I thought. Great results. Momma is pleased and is no longer complaining that we have to buy a new $1,000 washer ! Read more
Washer won't fill, overfills, or leaks? A faulty water inlet valve is often the cause. DIYers report 10-20 minute fixes for this common washer repair.
I ordered the replacement inlet valve from your site, installed it in 20 minutes. the washing machine now fills to extra large capacity in 3 minutes. The machine is an old Kenmore bought new in 1985, this inlet valve is the only component to fail in the over 30 years we have had it. Read more
Usually ships within 4 - 14 days
Fix low water flow or FL error code issues with this washer water inlet valve. Controls water flow into your machine. Moderate DIY repair, 30-45 minutes.
Replaced flow valve Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.