Admiral Hose Or Tube

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Includes connector and both clamps.

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

Size: 1/4" to 1/4" John Guess coupler. Compression fitting is also acceptable.

This right-angle elbow fits between the water supply line and the refrigerator's icemaker fill tube. It directs water cleanly into the icemaker and helps maintain a sealed connection to reduce drips and leaks. What it does:

• Connects the inlet water tubing to the icemaker fill tube at a 90-degree angle
• Routes water into the icemaker during the fill cycle
• Helps maintain a watertight connection at the rear of the cabinet
• Common symptoms: leaking behind the refrigerator, slow or no ice production, ice buildup near the fill area

• 1 fill tube elbow fitting

• Unplug the refrigerator and turn off the water supply; relieve line pressure before starting
• Access the rear lower area, place a towel for any residual water, and locate the elbow at the fill tube connection
• Release the clamp or retainer, disconnect the tubing, seat the new elbow fully, and resecure the line
• Turn water back on, check for leaks, then restore power and monitor the first ice fill

This drain hose carries used water away from your appliance during the drain cycle. Replacing a worn or damaged hose helps stop leaks and restores proper draining performance.

• Routes wastewater from the appliance's drain system to the household drain
• Replaces hoses that are cracked, brittle, clogged, or kinked and leaking
• Can help when cycles end with standing water or slow/failed draining
• Helps reduce odors and backflow when installed and routed correctly

• Disconnect power and water supply; allow the appliance to cool before servicing
• Move the unit for access; keep towels or a pan handy to catch residual water
• Transfer and tighten existing clamps/fittings to the new hose; route without kinks and secure per your model's instructions
• Run a short test cycle and check all connections for leaks

Replacement flexible hose that routes water inside your appliance, restoring secure flow and helping prevent leaks or drainage problems caused by cracked, kinked, or worn hoses. What it does:

• Directs water to and from appliance components during normal operation.
• Prevents leaks when hose walls and fittings are intact.
• Common symptom fix: visible leaks, water pooling beneath the appliance, or reduced/irregular water flow.
• Fits in-line with existing clamps and fittings to maintain proper routing.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect and replace clamps or fittings if corroded or damaged; use proper-size clamps for a secure seal.
• Route hose without sharp bends or kinks and avoid contact with hot surfaces or moving parts.

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

5 foot. Package of 2.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks