Admiral Washer Parts

• Will not fill with water
• Leaking

SCREWED IT ONTO FAUCET Read more

Put in new lid lock. This is my second one in 1 year. Whirlpool suggested I leave it loose so that if somebody did try and force it open, it wouldn't break it. This lid lock has 4 wires and cannot be bypassed. Read more

The parts I purchased from Appliance Parts Pro fit perfectly and were reasonably priced. I received them the next day, which made the Wife (and me) very happy. Although Appliance Parts Pro did not have a repair video for this, I was able to find one online and the machine is washing like new again. The website is well laid out and easy to find what your looking for. Between the available parts and the videos they provide, anyone who is reasonably handy should be able to repair their machine as... Read more

Removed the front panel and removed the screw from the console which revealed a broken plastic tab on the right side of the old injector. Replaced the old injector with the new one and that took care of the problem. Read more

• Will not drain

Removed old pump and discoverd that two impellers were broken and that bearings were shot orderef new pump which recieved next day and installed workinh fine now Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

Replaced mounting stem and tub bearings Read more

Ordered the right part, took the back off the top control panel, and popped it in. Read more

• No hot or cold water

I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more

I replaced the entire agitator (my appliance agitator could only be replaced in one part not the upper part only). It was super easy but one thing....the video on the website was not helpful because my maytag washer is older and does NOT have a screw down inside the agitator but has one 1/4 inch hex nut on the side down by the base. Good for me though because all I had to do was unscrew the nut, put the new agitator on, tighten the new nut and DONE!! Read more

With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more

I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more

A few screws and 15 minutes later it was done. Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more

I had removed three screws behind the control board cover of the washer, to access the old lid switch. I checked the continuety of the of the switch with a multimeter and it obviously failed the the test by displaying infinity of <1, rather than being 0. I removed the old switch with a flathead screw driver, I tested the new one and installed it in no time. Problem solved!!! Read more

• Lid or door won't close

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more