Amana Dryer Parts

I decided the problem was with the gas valve and I found the part on your web site. I ordered it and received the part in 3 days. I replaced the valve and the dryer works like new! This also gave me an opportunity to vacuum out the dust/lint that collects in and around the dryer. Read more

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

There is no good diagram explaining how exactly these fit in. I had to do trial and error. The parts are quite delicate so I actually broke one trying to get it in. I would recommend ordering an extra or two. These need springs tonfit correctly. Luckily I saved the old ones...if you don't have them, it won't work. Unscrew the two screws on outside and two inside. You don't have to take whole thing out, just loosen. Look carefully and you can see the two little holes in the plastic where... Read more

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

Remove bottom panel, remove top panel, remove drum. Had to cut old squirrel cage off. Remove motor to remove old wheel shank. Remove belt switch, and replaced. Videos from AppliancePartPros helped a lot.. Read more

Was an easy fix with the new part and instructions. Read more

I checked the continuity on the thermal fuse (which was blown) and knew that it needed to be replaced. This made me question why it blew (i.e. what caused it to fail). I checked continuity on the thermostat (high limit) as well as the thermostat for the element. Both passed a continuity test, so I removed the high limit thermostat to inspect it and could hear it rattling inside. This leads me to believe the spring inside had failed, so I replaced this thermostat as well. Put it back... Read more

Went on line looking on how to accomplish this and Appliance parts pro site came up and it was exactly what I needed. Order was sent on Sunday note and on Tuesday afternoon it was delivered. Just got done installing. Took longer to gather up the needed tools then to install. The instructions were awesome . complete wife great photos Read more

Replaced timer Read more

When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more

In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more

• Too hot

Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more

Ordered a replacement valve and installed it. The part from AppliancePartsPro was an exact replacement for the original part. Replaced the hot and cold hoses at the same time to insure no leaks. Cold water settings now work properly again. Read more

Purchased a new sensor from AppliancePartsPros.com. Installed new part - Problem fixed. Read more

• Too hot

I replaced the main parts for the dryer cycle system Read more

Repair was very easy. No instructions included but basically start the new seal tabs at the bottom in the middle and work your way around snapping in place. 60 seconds Read more