Amana Dryer Parts

Removed the heater of course and installed the part. Very easy to do no need to remove the drum, just top cover, control panel, and front door assembly. Remove the one screw holding heater, remove blue wire, turn heater CCW to the 8 o'clock poisiton. Install in the reverse order. This is the secound one in a month if it fails again i'll just bypass it and install a 25 AMP fuse. Read more

I took the dryer apart.....first had to clean out all the lint here and there. Took the drum out, inspected the belt and back support wheels. They seemed to be fine. In the front the drum turns on two supports that have a Teflon glide. Those two glides had been worn off with their pad so metal was rubbing against metal. Went online to appliancepartspros.com and looked up on the schematic what parts I needed. I also had called around locally and the same parts cost twice as much....so I... Read more

I had to remove my dryer so I could install a new floor. The dryer would not fit through the doorway with the power cord attached. Since the power cord was fastened to the back using 3 phillip headed screws, I gently backed them out with a phillip headed screwdriver. However, two of the 3 screws gave me extreme trouble. The head of the screws were made of such a weak metal, that the screw head began stripping. I have a phillip screw kit with different sized heads, so I picked a head that... Read more

Unfortunately my first repair attempt (replacing the Gas Valve Coils) failed so I decided to replace the entire Burner assembly. From a cost/time point of view the Burner assembly is a better value than just buying the Gas Valve seeing as you don't have to disassemble/reassemble most of the existing Burner (to get to the Gas Valve) *and* you get a new Igniter!! The most annoying thing about the repair is accessing the screw that clamps the gas pipe to loosen it :-(... Read more

Valve (or a component on it) was slowly leaking gas. I was able to easily replace the entire gas assembly with this order. Item was mostly pre-assembled, and contained all parts needed, including new igniter and coils. Read more

Reasonable price for dryer rack and fast delivery = excellent customer service; will buy again Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more

• Shuts off too soon

Replaced heating element about three months ago. Had to order thermistor because of error code "ts" on display and dryer would not run. Removed the two screws on the back that holds the top in place. After removing the top, remove the screws that hold the control panel on front. Make sure not to break the tabs that help hold it in place You do not have to unplug any connectors for the control panel. Lay control panel across top of dryer carefully so that it will be out of the way. Next... Read more

I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only... Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

Replaced several hinge parts. Read more

• Timer will not advance

I went ahead and ordered the element, and the 2 different thermostats not knowing exactly which one might be the problem. My My Maytag opens from the front and it was actually pretty easy to get into. Also gave me the opportunity to vacuum out the inside of the dryer. Pop the top off, remove the wires that connect the door switch (noting the colors and placement), take off the 2 inside nuts that hols the fron on, pull it forward and lift it off, 3 inside screws to take out to inside lint part... Read more

We got the heater core kit. Unplug, undo two screws and pulled old one out. Looking at the old one, put the new one together and then mounted it back in place. Turned on dryer but no heat so unplugged it, tapped on elements, plugged back in and it worked. Not to hard. Read more