Amana Range Heating Element

Restore reliable heat to your electric range or cooktop with this surface heating element. Replacing a failed top-burner element brings back consistent, even heating so pots and pans heat up properly at your chosen setting.

• Supplies electric heat to a cooktop burner zone when turned on
• Common fix for a burner that won't heat or only partially glows/heats
• Helps address uneven or slow heating on the affected element
• Replace if the element shows visible breaks, blisters, or has shorted

• Disconnect power at the breaker and allow the cooktop to cool completely before service
• Access varies by model; support and protect glass tops when lifting/removing
• Photograph wiring; transfer any original brackets, insulators, or limiter/thermostat if present
• Ensure clean, tight terminal connections; fully reassemble before restoring power

This surface heating element powers one of your range's top burners, restoring steady, responsive heat for everyday cooking. Replace a failed element to bring your cooktop back to consistent performance when boiling, simmering, or sautéing.

• Provides heat to the selected surface burner when the control is turned on
• Works with the burner switch to reach and maintain set temperatures
• Common symptoms of failure: burner won't heat, heats unevenly or intermittently, or shows visible damage/hot spots
• Helps resolve long heat-up times and inconsistent cooking results

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing.
• Access and mounting vary by model; note wire locations and transfer any brackets/clips from the original element.
• Inspect terminals and connectors; replace any heat-damaged wiring or receptacles before reconnecting.
• Handle by the frame and avoid stressing the element; ensure secure electrical connections before testing.

This electric range broil element installs at the top of the oven to deliver direct radiant heat for broiling. Replacing a burned-out or damaged element restores fast, even broil performance and consistent top heat.

• Provides high, direct heat from the top of the oven during Broil to sear and brown food
• Common fix for: broiler not heating, weak or uneven broiling, visible blisters/cracks on the element, or sparking during broil
• Mounts at the upper oven cavity; connects to two push-on terminals
• Helps restore consistent top heat and even browning when functioning correctly

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; unfasten mounting screws/bracket, gently pull element forward, and disconnect the wire terminals (support wires to prevent them from falling back)
• Transfer existing mounting hardware if needed; ensure terminals are fully seated and insulated—do not overtighten screws
• The element is clear of the oven liner; restore power and test Broil

This 2000-watt surface heating element restores steady, responsive heat to a cooktop burner. Replace a weak or failed element to bring back quick heat-up and even, consistent cooking performance. What it does:

• Supplies up to 2000 watts of heat to the selected burner zone
• Works with the surface control to achieve and maintain set temperatures
• Common fix for: burner not heating, slow or uneven heating, or intermittent operation
• Replace if the element shows visible damage such as cracks, blistering, or burned spots

• 1 surface heating element (2000W)

• Disconnect power at the breaker and allow the cooktop to cool fully before servicing
• Lift/remove the cooktop to access the element; handle the glass carefully
• Move wires and any mounting clips from the old element to the new one, one connection at a time, matching positions
• Secure connections before reassembly; if issues persist, inspect the surface switch and wiring harness

Restore steady cooking performance with this surface element coil. The 6-inch, 1250-watt burner replaces a worn or open coil so your range heats properly for everyday simmering, sautéing, and boiling.

• Generates heat on a 6-inch cooking zone for boiling, sautéing, and simmering
• Fixes a burner that won't heat or only heats intermittently
• Addresses uneven heating or unusually slow warm-up
• Helps when the coil shows visible breaks, blistering, or burned spots

• Disconnect power at the breaker and let the cooktop cool completely
• Remove the old coil and inspect the receptacle/terminal block; replace if burnt or loose
• Align prongs and press the new coil fully into the receptacle; ensure the support bracket seats in the drip pan notch
• After installation, test the burner with a pan to ensure even heating

This lower oven bake element restores the primary heat source for Bake cycles in electric ovens. A failed element can cause no heat or uneven results; replacing it brings back consistent preheating and baking performance.

• Heats the oven cavity from the bottom during Bake mode
• Replaces a broken, shorted, or visibly damaged element
• Common symptoms: no heat in Bake, slow preheat, or uneven baking
• Helps the oven maintain set temperature once preheated

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove mounting screws; gently pull the element forward to access and disconnect the two spade terminals
• Transfer wires to the new element, secure with existing hardware, and ensure wiring/insulation isn't pinched
• Restore power and test a Bake cycle

This 6-inch radiant surface element is the heating source for a small burner beneath a glass-ceramic cooktop. Replacing a failed element restores reliable, controllable heat to that cooking zone. What it does:

• Heats the 6-inch cooking zone under the glass top when the control is turned on
• Cycles to help maintain the selected temperature during cooking
• Common symptoms of failure: small burner won't heat, heats unevenly or intermittently, or shows visible burn spots/damage

• 1 six-inch radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift the glass top or remove the cooktop to access the elements; support the glass to avoid stress or cracks
• Note wire positions and transfer connections to the new element one at a time
• Ensure the element sits flat in its mounting brackets before reassembly and testing

This 8-inch coil surface element restores reliable heating on the large burner of electric ranges and cooktops. Its 2350-watt design provides steady, even heat for boiling, frying, and everyday cooking.

• Converts electrical power into heat for the large cooktop position
• Common failure symptoms: no heat, uneven heating, only part of the coil glowing, visible breaks or blisters, or failed continuity
• Plug-in coil style for receptacle-type burner sockets
• If no heat persists after replacement, also inspect the element receptacle and the burner switch

• Disconnect power to the range/cooktop and allow the element to cool completely
• Lift the old element and pull straight out from the receptacle
• Align the new element's terminals with the receptacle, push in firmly until fully seated, and set it into the support/drip bowl
• Restore power and test the burner

2100W. Size: 8 inch. Location: Right front.

1800 watt

This surface heating element is the electric heat source for a cooktop burner on an electric range. Replacing a worn or open element restores steady, responsive burner heat for everyday cooking. What it does

• Converts electrical energy to heat for the selected surface burner
• Works with the surface control to cycle heat and maintain set temperature
• Common symptoms: burner won't heat, heats weakly or intermittently, or shows visible hot spots/burn marks on the element

• 1 surface heating element

• Disconnect power at the breaker before servicing and let the cooktop cool completely
• Access the element by lifting/removing the cooktop or burner pan per your model's service procedure
• Photograph and label wire locations; move one connection at a time to the new element
• Transfer any mounting brackets or supports from the original element; avoid bending or stressing the element during install

Restore consistent bottom heat in your oven with this bake element. When the original element burns out, the oven may not heat, preheat slowly, or bake unevenly—replacing it restores dependable baking performance and even results. What it does:

• Supplies heat from the bottom of the oven during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common symptoms of failure: little or no heat in Bake, slow preheating, uneven baking/browning
• Visible signs can include blisters, cracks, or breaks in the element

• 1 bake element

• Disconnect power at the breaker and allow the oven to cool before service
• Remove mounting screws and carefully pull the element forward to access the wires
• Transfer the two wires to the new element, keeping them from slipping back into the oven cavity
• Reinstall mounting screws, restore power, and test Bake operation

• A healthy bake element typically shows continuity on a multimeter; an open reading indicates it has failed.

This lower bake element supplies the primary heat for Bake cycles, restoring consistent oven temperatures and even results. Replace a burned-out or damaged element to resolve no-heat on Bake, extended preheat times, and undercooked food.

• Heats the oven cavity from the bottom during Bake cycles for proper cooking
• Restores heat when the original element is burned out or broken
• Common symptoms: no heat on Bake, very long preheat, uneven or undercooked results
• Visible damage such as blistering, cracks, or breaks indicates replacement

• Disconnect power at the breaker before servicing
• Remove oven racks, take out the element's mounting screws, and gently pull the element forward
• Transfer the two wires one at a time; do not allow wires to slip behind the oven liner
• Reinstall the element and screws, restore power, and test Bake

This broil element provides the intense top heat your oven uses for broiling. Replace a failed or damaged element to restore consistent broiler performance and proper browning when broiling meats and other foods.

• Supplies high, direct radiant heat from the top of the oven during broil cycles
• Restores proper broiling performance for browning and searing
• Replaces elements with open circuits, blisters, cracks, or shorts
• Common symptoms include: broiler won't heat, weak or uneven broiling, visible damage, or the breaker trips when broil is turned on

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and disconnect wires; support wires so they don't slip back into the rear cavity
• Attach wires to the new element and secure with existing screws; avoid bending the element or overtightening
• Restore power and test the broil function

The Bake Element is an OEM part for Whirlpool ranges. As a heating component, this bake element is responsible for providing bottom heat during baking and roasting functions.

Causes of a bad bake element include deterioration of insulated coils and connections from continual heat cycling. Exposure to drips or spatters can damage their integrity over time.

Symptoms of a bad bake element include:

• Inability to heat up to desired cooking temperatures
• Slow or ineffective baking and roasting results
• Error codes or failure alarms from the control board
• Visible burnouts or breaks in the coil filaments

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 8-inch surface burner element delivers heat on an electric cooktop or range. Replacing a worn or open element restores even heating on the burner zone and reliable response to temperature settings.

• Heats the 8-inch cooking zone when the surface control is turned on
• Helps maintain consistent pan temperature for boiling, simmering, and frying
• Common symptoms: burner won't heat, heats unevenly or intermittently, visible blistering/breaks in the coil, or scorch marks at the terminals
• Replacing a damaged element can prevent further damage to the receptacle/terminal block

• Disconnect power at the breaker and allow the unit to cool completely
• Handle the element by the bracket; avoid bending the coil
• For plug-in setups, pull the old element straight out and firmly seat the new one; for wired connections, move wires one at a time to the matching terminals and secure properly
• Inspect the receptacle/terminal block and wiring; replace if burnt or loose before restoring power