Parts for Kitchenaid KF26M22SR5: 03 - Case, Gearing And Planetary Unit Parts

Hinged cover that protects the attachment hub on stand mixers. Replace if cracked, chipped, broken, or won't stay in place. Slides over housing grooves.

The Transmission Housing is an OEM part for Whirlpool mixers. This component encases the transmission, which is responsible for transferring power from the motor to the mixing attachments. The housing ensures the transmission is protected from external

If your mixer beater won't move or makes grinding noises, worn gears are likely the cause. This gear kit restores smooth operation. DIY-friendly repair.

Seals mixer transmission housing to prevent grease leaks. Replace if you notice grease on the mixer body or attachment shaft. Confirm fit with your model.

Mixer making noise or shaft loose? This retaining ring locks gears in place on the drive shaft. Moderate DIY repair with snap ring pliers required.

If your mixer beater won't move or makes grinding noises, worn gears are likely the cause. This gear kit restores smooth operation. DIY-friendly repair.

Mixer makes growling noise but beater won't spin? This steel retaining pin locks drive components in place. Moderate repair; disassembly required.

Fix a stand mixer that won't spin or makes grinding noises. This worm follower gear transmits power in the gearbox. DIY repair in 30-60 minutes.

Supports the planetary shaft for smooth rotation in your stand mixer. Replace if you hear grinding noises or mixing becomes uneven. Confirm fit by model.

The Gear is an OEM replacement part for Whirlpool stand mixers. Located inside the mixer head assembly, it transfers torque from the motor into rotary spinning of mixing attachments. Thorough blending and kneading depend on dependable gear movement.

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provide

Seals the motor shaft opening to prevent oil leaks and debris from entering internal components. Replace if you notice oil leaking or grease contamination.

Fix a mixer that won't rotate freely or makes grinding noises with this rear sleeve bearing. Supports the motor shaft for smooth operation. DIY repair.

Metal sleeve bearing that supports the mixer's rotating shaft. Replace if you hear grinding noises or see metal shavings in grease. Confirm fit by model.

Thrust bearing supports the worm gear in your stand mixer's drive system, reducing friction for smooth operation. Replace if you hear grinding noise.

Mixer slipping or making loud grinding noises? This worm gear transfers motor power to attachments. Moderate DIY repair with cleaning required.

Fix a mixer that won't run, starts at full speed then stops, or won't shift speeds properly. Replace the speed control board in about 30 minutes.

Replacement mounting screw for stand mixer panels, brackets, and trim. Secures internal components to keep parts aligned. Replace if missing, stripped, or rusted.

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and interna

Replacement thumb screw for stand mixer power hub. Secures beater, whisk, and dough hook attachments. Replace if cracked, broken, or missing.

Fix a mixer that won't run, starts at full speed then stops, or won't shift speeds properly. Replace the speed control board in about 30 minutes.

Mixer won't run or starts then stops? Drive motor failure is often the cause. Straightforward repair with basic tools, about 10 screws to remove.

Replacement power cord for stand mixers. Connects your mixer to the wall outlet. Replace if cord is frayed, damaged, or has exposed wiring.

Hardware washer for stand mixer planetary assembly. Replace when worn or missing to secure gears, reduce vibration, and prevent rattling. Confirm fit.

The Retaining Clip is an OEM part for Whirlpool stand mixers. This small but essential part ensures the stability and secure fitting of various mixer components, contributing significantly to the appliance's overall performance and durability. Its

The Washer is an OEM replacement part for Kitchenaid stand mixers. This washer is used as a spacer and insulator between gears to provide protection to the planetary bushing on the stand mixer.

Causes of a bad washer can include wear over

The Pinion Gear is an OEM replacement part specific to KitchenAid stand mixers. It is a small gear located within the planetary mixing mechanism. The pinion gear works with the worm gear to power the planetary action that thoroughly mixes ingredients.<

Flat metal washer that acts as a hardware spacer in stand mixers. Distributes clamping force where screws or bolts secure components. Replace if worn or missing.

If your mixer beater stopped spinning or spins loosely, this agitator shaft assembly transfers motor power to turn attachments. Moderate DIY repair.

If your stand mixer components are loose or misaligned, this grooved retaining pin secures parts together for smooth, quiet operation. Easy fix.