Cooktop Pilot

This pilot burner supplies the standing pilot flame for the right-side surface burners on standing-pilot gas ranges. Replacing a clogged or damaged pilot restores consistent ignition and a stable flame for reliable burner lighting.

• Provides the small, continuous flame that lights the right-side surface burners when their valves are opened
• Helps maintain correct pilot flame size and positioning for dependable crossover ignition
• Safe symptom clues: pilot won't stay lit, weak/yellow flame, intermittent or no lighting of the right-side burners, needing a match to light
• Physical damage or blockage from spills/debris can impair operation

• Disconnect power and shut off gas before servicing; allow the appliance to cool
• Access the pilot area; note routing and orientation before removal
• After reconnecting, check all gas connections with an approved leak-detection solution
• Adjust the pilot flame to manufacturer specifications and re-light pilots as required

This pilot burner supplies the small, continuous flame that lights the surface burners on gas ranges/cooktops, helping ensure reliable burner ignition and steady performance.

• Provides a steady pilot flame to ignite the surface burners
• Helps restore lighting when surface burners won't ignite or the pilot won't stay lit
• Can address weak or inconsistent pilot flame at the top burners
• Typical signs include repeatedly having to relight the pilot or burners going out during use

• Disconnect electrical power and shut off gas before servicing
• Allow the appliance to cool and ventilate the work area
• Inspect and clean mating surfaces; replace brittle tubing or cracked fittings as needed
• After installation, check for leaks and adjust the pilot flame per the service manual

This pilot burner assembly ignites the oven's main burner and restores reliable pilot flame control for gas ranges and ovens. Use to replace a worn or malfunctioning pilot that won't hold a steady flame. What it does:

• Provides the small, continuous pilot flame required to light the main burner
• Helps resolve symptoms like a weak or out pilot flame, intermittent ignition, or oven that won't light
• Direct replacement for the OEM pilot burner assembly designed for compatible gas ovens
• Works with factory gas control and ignition components when installed correctly

• Turn off gas supply and electrical power to the appliance before servicing
• Inspect the gas orifice and pilot tube for debris; clean gently if needed
• Use appropriate hand tools and tighten fittings to manufacturer torque specs — do not overtighten

This thermocouple monitors the burner flame and works with the safety valve. It allows gas flow only while a flame is present and lets the valve close when no flame is detected, helping restore dependable burner operation.

• Senses burner flame heat and sends a small millivolt signal to the safety valve
• Works with the flame-failure safety system to maintain or cut gas flow based on flame presence
• Common symptoms can include: burner lights but goes out when the knob is released; needing to hold the knob down unusually long to keep the burner lit

• Disconnect power and shut off gas before servicing
• Allow the unit to cool; remove grates/caps to access the sensor tip and route the lead to the valve connection as originally installed
• Do not kink or sharply bend the lead; position the tip within the burner's flame envelope
• After reassembly, restore gas/power and test burner operation

This pilot thermostat is the oven temperature control that senses heat and helps regulate burner operation for consistent cooking. It replaces a worn or faulty thermostat to restore accurate temperature response and reliable oven ignition. What it does:

• Senses oven temperature and signals the burner/pilot system to maintain set heat levels
• Helps the oven light and hold temperature when the pilot or main burner is used
• Commonly used when the oven won't heat, cycles excessively, or fails to maintain consistent temperature
• Works as the temperature-sensing control element in gas oven pilot systems

• One pilot thermostat

• Turn off power and shut off gas supply before starting any service
• Handle thermostat gently; avoid bending or stressing the sensing element or capillary tube
• Verify wiring connections match the old part; replace like-for-like

This thermocouple is the flame-sensing safety sensor used on gas ovens and ranges to detect a pilot or burner flame and allow the gas valve to stay open. It replaces a worn or failed sensor to restore proper flame detection. What it does:

• Senses pilot/burner flame and signals the gas valve to remain open when heated
• Prevents gas flow if the flame goes out, improving appliance safety
• Commonly replaces thermocouples that are bent, corroded, or no longer reach operating temperature
• Can resolve symptoms like burners or oven not staying lit, or intermittent ignition

• Disconnect power and shut off the gas supply before starting work
• Handle the sensor tip and tube gently; avoid kinking or over-bending the probe
• Verify proper seating and secure connection to the gas valve and pilot assembly