Cooktop Latch, Catch, Lock Parts

• Door won't close
• Door stuck closed

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

Replaced the cheap plastic lever supporter with another LG OEM cheap plastic lever supporter. I should have bought two as I can see this problem happening again. Job was a simple fix and only required a Phillips head screwdriver. I did not need to remove any connections as there was enough room and wire to pull out the oven control assembly and make the repair. One word of caution is to be careful as the sheet metal internal cover and bottom of the control knob panel is razor... Read more

Replaced the part. Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more

Replaced the latch. Everything works fine now Read more

With parts from you my son repaired the door and now microwave is operating perfect.,.... A 10 minute job for him!... Thanks for not having to buy a new one!!!!! Read more

• Door stuck closed

Turn off breaker, remove all screws { 4 on mine } inside oven door holding oven and microwave to kitchen cabinet and slide oven assembly out of cabinet {on to a temporary shelf of {4} 5 gallon buckets/plywood/bricks/shims that I made on the floor atop a scrap of carpet} just enough to access the side and rear screws of microwave's protective metal housing, then remove a total of 16 screws { there were 2 screws just inside top of "opened" microwave door that were holding top flat silver metal... Read more

• Door won't open after self cleaning cycle

I knew the door latch was suppose to lock for self clean and it wasn't, so I took the back off and after tracing out wires and the linkage to the door latch, determined that it was a faulty motor on the latch lock. I got on line and Appliance Parts Pros was the first place that I found the part. I was surprised that it wasn't real expensive, but I kept looking for a cheaper price only to come back to order it from APP. I order it around 9:00 on a Thursday night and it was on my front porch... Read more

Everything works great, but my Jenn-Air stove is more than 15 years old and really needed a face lift. To replace it will cost about $3000.00 to replace, to replace missing and old parts around $500.00. Thankfully Appliance Parts Pros had all the parts I needed to make my stove look as good as it works. Read more

I replaced the latch and handle assembly. It's easy when you see how it goes together. Unscrew the two screws under the front edge of the stovetop, have a helper lift the stovetop up, unscrew the six screws holding the metal plate down and remove the plate, unplug the wires connected to the latch switch, and unscrew the two front screws holding the latch assembly in place. Replace the latch assembly and put it back together in reverse. Read more

Between YouTube, a multimeter and Appliance Parts Pro I was able to diagnose the problem and fix the oven without an expensive service call. Read more

Bought a new key. Great service and had the item the very next day. Read more

My appliance is a Whirlpool Accubake Wall Oven, single door. After using the tech sheet and measuring the ohms of the two micro switches that sends signals when the door is shut and locked, determined the lock was faulty. Pretty simple to change, the most difficult part was taking the digital face off of the oven without damaging the control board. TIP: take a picture of the latch switches to ensure you put the correct wires on the correct switch. Read more

• Won't start
• Will not agitate
• Will not drain

Replace the broken switch Read more