Craftsman Blade

A flail blade is a mechanism most often found in wood chippers and shredders. It is compatible with products by brands such as MTD, Troy-Bilt, Yard Machines, Cub Cadet, and Yard Man.The flail blade part is made out of what is commonly referred to as teeth or knives. The purpose of the flail blade is to serve the machine with the short pieces of metal attached to an axle that turns rapidly. A flail blade is capable of cutting grass and other plants. A flail blade can be mounted on the front, back, or side of outdoor machinery.This flail blade is made out of metal. This flail blade is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

This left-hand bolo tine is a replacement part used for a tiller. This part is constructed of black metal and requires a wrench set for installation. This tine easy to install. The left-hand bolo tine attaches to the left tine holder and is used to dig up dirt in the area being tilled. This is a genuine OEM part sourced directly from the manufacturer and is sold individually.The left-hand bolo tine should be replaced if it is damaged or no longer working. If the tines become so worn that they are pointed, the tiller will not perform acceptably. The tiller will not dig as deeply nor will chop garden residues and cover crops. The tines are typically to be replaced as a set rather than individually.To replace the tines, begin by removing the sheer bolt with a wrench that connects the tine assembly to the tine shaft. Next by using either a wrench or small impact driver, remove all nuts and bolts disconnecting the tines from the tine holder. Replace the left-hand and right-hand tines, tightening with either a wrench or small impact driver, and reattach the tine holder assembly to the tiller securing it with the sheer bolt. The tines should slant into the inside of the tine holder. The tiller is now ready for use. This part is manufactured by Troy-Bilt and MTD.

This blade adapter has a 25mm inner diameter and fits onto the blade of a variety of lawnmowers. The blade adapter allows the blade to connect to the spindle for proper performance. This blade adapter is made of metal. Regular wear and tear can cause the blade adapter to go bad or even split in half. When this happens, the blade adapter will need to be replaced.Before replacing the blade adapter, the lawnmower should be turned off and the spark plug wire needs to be disconnected. Turn the mower upside down to get access to the component. Use a socket set to remove the old blade adapter and replace it with the new component. Replace any other components, connect the spark plug wire, and test the machine before use. This component is sold on an individual basis. It is an authentic OEM replacement part that is directly sourced from the manufacturer. The blade adapter is made to be used with lawnmowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, MTD, Troy-Bilt, and Yard Machines.

This chipper blade is an authentic OEM replacement part sourced directly from the manufacturer for use in chipper shredders. The blade is the workhorse of the machine, chopping the limbs and sticks into tiny particles as they pass through the machine. As the machine is used, the blades will become dull and need sharpened. Eventually, the blades may develop cracks or become so worn that they need to be replaced for the chipper to function efficiently. Chipper blades should be periodically inspected.Wear safety gear and remove the chipper's spark plug before working on the blades. Remove the bolts holding the hopper in place and set the bolts and hopper aside. Remove the housing protecting the rotor assembly and chipper blades. Remove the bolts holding the chipper blades in place. Discard the old blades. Install the new blades and reassemble the chipper. Put the spark plug back in and test the blades.This chipper blade is made of heavy-duty metal and is sold as an individual part. It does not include connecting bolts. This blade is designed for use in chippers manufactured by MTD and Troy-Bilt.

This is a chipper impeller assembly that can be used with a range of chippers and chipper-shredders. The impeller is the part of the chipper that rotates, and it is what allows for the chipping or shredding to take place. It will shred leaves, yard waste, and tree limbs. If there is an issue with the chipper impeller, it will reduce the efficiency of the machine. In some cases, it might not work at all. One of the signs that the impeller has problems is that it is turning slowly. It might also make a lot of noise.The impeller is a durable piece, but it does a lot of work. This means it is subject to wear and tear. Over time, it might become worn out or damaged, which will require a replacement. This replacement could be done by the owner. However, they need to remove the spark plug wire first and wear gloves to keep their hands safe.The chipper impeller assembly works for select machines from MTD, Troy-Bilt, Husky, and Yard Machines. This is a genuine OEM replacement part sourced from the manufacturer, and it is sold individually.

This is a chipper blade, which is installed on wood chippers and is used for cutting up pieces of wood into small chunks. Chipper blades need to be sharpened at least once a year or after about 25 hours of use. If the chipper blades aren't maintained, they will become dull and won't provide the required level of cutting power needed for wood chippers. If wood chips from the chipper are uneven, shredded, or rough, then sharpening or replacement may be needed. Make sure to take out the spark plug before the hopper is removed and connected to the tool. Next, remove the housing around the blades and the rotor assembly. The bolts around the blades can be taken off using an Allen wrench. Remove the blades, but be sure that work gloves are used to prevent injury. The replacement blade can be installed at this time. This is an OEM replacement chipper blade that can be used on wood chippers from Craftsman, MasterCut, Cub Cadet, Yard-Man, Yard Machines, and MTD. It's sold individually and comes directly from the manufacturer. The replacement will require an Allen wrench set, a wrench set, a socket set, and pliers.

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

This scraper blade is an authentic OEM replacement part for a snowblower. Snowblowers operate using an auger that scoops up the snow and blows it to a different location. However, an auger cannot gather all of the snow because it would have to scrape against the ground. Scraping that auger against the ground would damage its blades and make them unusable. Instead, this scraper blade drags against the ground and collects any remaining snow so that the auger blades can remain protected. Scraper blades can be damaged if the snowblower goes over rocky terrain. Although it is nearly impossible for a blade to snap completely off a blower, the blade will leave the snow behind, making the blower less effective if chipped or dented. To replace a scraper blade, simply use a socket wrench to unbolt the blade from the auger housing. Be sure not to lose the bolts as they will be needed for reassembly. This part is compatible with Craftsman, MTD, Cub Cadet, Ryobi, Huskee, Yard Man, and Yard Machines snowblowers and is sourced from the original manufacturer. This part is a high-quality replacement part. It does not ship with additional hardware.