Crosley Parts

• Won't start

I removed the belt and found with no load the motor ran but made a grinding noise. I purchased a new motor and installed it. The fix was easy and quick. Read more

• Element will not heat

Very easy. go online learn how to change the element step by step. order the part and you are all set. I saved $99 of labor cost. Read more

• Element will not heat

1. Went online where I watched video about heat control for this Maytag. I then found AppliancePartsPros using Google. I ordered the part and In three days the part arrived. I installed the part and now the problem has been corrected. Read more

I ordered three parts for my fridge. The entire process was so easy! I entered my model number and quickly found the parts I needed! Submitted the order and the parts arrived the Next Day! I was very happy! Read more

• Little to no heat when broiling

Removed old element , found the part on exploded view diagram of th oven. Got on appliance parts pro web site put in model number , made sure picture on line looked the same and ordered. While I was at it ordered a bottom pan for the oven that needed replacing. Received both parts 3 or 4 days later regular shipping. Installed both parts no problem . Thanks appliance parts pros. Read more

Came home from a shopping trip to find our new Frigidaire oven handle on the floor. Notme did it. Anyway, looked up sources for parts and found these guys. Ordering was easy and delivery quick. All I needed was a #2 Phillips screwdriver and we were back in business 10 minutes after the part arrived. Read more

The ridges inside the agitator base were stripped. Installed a new base - after a good cleaning of build-up on the spindle. Works like new! Read more

Unplugged unit from power. Removed two sheet metal screws and lower front panel, removed two sheet metal screws and door panel (disconnected three door switch wires and two light wires - noted the connected position of each wire ); removed three self-tapping screws and black plastic hot air outlet to fan duct from lower end of front bulkhead; removed sheet metal screws and front bulkhead; removed two sheet metal screws from dryer top panel and raised top up and back on rear hinge brackets;... Read more

Replaced control board. Did not need Control Thermistor in my case, but I'm keeping it as backup. Got the Drum Belt just in case it breaks on me since the dryer is aging. To replace control board: Disconnect power and pull dryer away from wall. Take 2 black screws on the back off to remove the top lid. Remove 2 screws on top that hold the control interface on. Remove 2 screws on the bottom backside of the control. Pull out control panel and pull off terminal connections and push to remove... Read more

• Little to no heat when baking
• Won't start

We replaced the broken Terminal Block but have not yet replaced the Control Panel. Will purchase that part from you shortly. Read more

• Leaking

After discovering your web site and reading of others issues I ordered a door seal (my old one was a little short on the right side) a detergent door grommet, and the 2 water deflectors ( I decided to cover all the bases while I was at it. Very simple job with the information provided on your web site. I certainly have the confidence to tackle other appliance repair now. Read more

After tracing the water dripping back up through the inside of the washer I found the water dispenser inlet valve was leaking. I watched several videos to make sure I understood what was involved. I contacted a local parts company to get the part. I also searched online for the part. I found that AppliancePartsPros.com had it cheaper. I ordered late in the afternoon and it arrived the next day. It was fairly easy to installed and saved me a minimum of $99 "diagnostic" fee plus whatever the part... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

I research it online and found that my timer knob skirt was cracked, watched the video online to see how to fix it, ordered the part………it came within 2.5 days. I followed the instruction on the video and was able to fix it myself. I love that I am able to fix things like this myself, I will use this site again for my next repair needs. Thank you Read more

I ordered the replacement part from Appliance Parts Pros. It arrived a few days later. A helpful video on YouTube showed me how to do it. The baffle was replaced in approx. 1/2 hour. Thank you AppliancePartsPros for you courteous help and speedy delivery. I will return when in need. Read more